Parti

Nessuna parte richiesta.

Slide the back cover down with your thumb.
  • Slide the back cover down with your thumb.

  • *Note: the battery cover is not shown in this picture

Aggiungi Commento

Gently lift the battery with a fingernail and remove it from its housing. *Note: the battery may be replaced or repaired at this step
  • Gently lift the battery with a fingernail and remove it from its housing.

  • *Note: the battery may be replaced or repaired at this step

Aggiungi Commento

On some models, the front case is screwed down from the back.  Follow steps 5 and 6 FIRST to remove the camera cover and two T6 screws, before removing the faceplate. Use the Spudger to gently pry up the edges of the front face plate At the center of the faceplate edge below the music keys there is a small latch on each side.
  • On some models, the front case is screwed down from the back. Follow steps 5 and 6 FIRST to remove the camera cover and two T6 screws, before removing the faceplate.

  • Use the Spudger to gently pry up the edges of the front face plate

  • At the center of the faceplate edge below the music keys there is a small latch on each side.

Before doing this step, first remove the camera cover and the two t6 screws from the back (steps 5 and 6). Otherwise you will break the cover. This may be a factor only for some revisions (RM-304)

s c - Replica

Lift up the keypad from the bottom with either the spudger or your finger. Note: at this time the keypad can be removed and replaced
  • Lift up the keypad from the bottom with either the spudger or your finger.

  • Note: at this time the keypad can be removed and replaced

Aggiungi Commento

Gently unsnap the back camera cover from the phone.
  • Gently unsnap the back camera cover from the phone.

  • Lift the cover from the phone after it is unsnapped.

Aggiungi Commento

Use the T6 torx screwdriver head to remove the 2 screws on either side of the camera Flip over the phone and again us the T6 torx head to remove the 4 screws located at each corner of the white keypad base
  • Use the T6 torx screwdriver head to remove the 2 screws on either side of the camera

  • Flip over the phone and again us the T6 torx head to remove the 4 screws located at each corner of the white keypad base

Aggiungi Commento

Unclip the faceplate plug (ribbon) located in the lower left corner of the motherboard
  • Unclip the faceplate plug (ribbon) located in the lower left corner of the motherboard

Aggiungi Commento

Use the Spudger to pry up the 2 metal clips located near the center of the motherboard on both the left and right At this point the phone should come apart into 2 pieces, the motherboard/LCD screen and the faceplate
  • Use the Spudger to pry up the 2 metal clips located near the center of the motherboard on both the left and right

  • At this point the phone should come apart into 2 pieces, the motherboard/LCD screen and the faceplate

Aggiungi Commento

Unclip the ribbon plug located on the top of the LCD screen that connects it to the motherboard
  • Unclip the ribbon plug located on the top of the LCD screen that connects it to the motherboard

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 5 persone hanno completato questa guida.

Max Kirby

Membro da: 01/05/2011

497 Reputazione

8 Guide realizzate

Team

Cal Poly, Team 15-14, Regan Spring 2011 Membro di Cal Poly, Team 15-14, Regan Spring 2011

CPSU-REGAN-S11S15G14

3 Membri

8 Guide realizzate

Thank you much! As efficient & thorough as it gets!

REDACTED FREE PRESS - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 4

Ultimi 30 Giorni: 11

Tutti i Tempi: 8,109