Remove the two Phillips screws securing the battery cover to the back of the handheld console. Lift the battery cover off the back of the DSi XL.
  • Remove the two Phillips screws securing the battery cover to the back of the handheld console.

  • Lift the battery cover off the back of the DSi XL.

Aggiungi Commento

Lift the battery from the DSi XL.
  • Lift the battery from the DSi XL.

Aggiungi Commento

Remove the four rubber screw covers on the lower case by prying them up with a push pin. Remove the four rubber screw covers on the lower case by prying them up with a push pin. Remove the four rubber screw covers on the lower case by prying them up with a push pin.
  • Remove the four rubber screw covers on the lower case by prying them up with a push pin.

Aggiungi Commento

Remove the following seven Phillips screws that secure the lower case to the rest of the DSi XL:
  • Remove the following seven Phillips screws that secure the lower case to the rest of the DSi XL:

    • Four silver 5.3 mm screws

    • Two black 5.3 mm screws

    • One black 2.5 mm screw

Aggiungi Commento

Kit RAM Mac
Accelera il Mac. Porta la memoria al massimo.
Kit RAM Mac
Metti più memoria nel tuo Mac.
Turn the DSi XL over, and open the display. Insert a spudger between the upper and lower case at the bottom left corner of the DSi. Slide the spudger along the bottom edge of the upper case to release the latches securing the upper case to the lower case.
  • Turn the DSi XL over, and open the display.

  • Insert a spudger between the upper and lower case at the bottom left corner of the DSi.

  • Slide the spudger along the bottom edge of the upper case to release the latches securing the upper case to the lower case.

Aggiungi Commento

Close the display and turn the DSi XL over. Lift the lower case from the front edge.
  • Close the display and turn the DSi XL over.

  • Lift the lower case from the front edge.

  • Rotate the lower case away from the DSi.

  • The lower case cannot be completely removed yet, since it is still connected to the motherboard.

Aggiungi Commento

Using a spudger, pry the SD card/right shoulder button connector off its socket. Pry the volume button/left shoulder button connector off its socket on the motherboard with a spudger.
  • Using a spudger, pry the SD card/right shoulder button connector off its socket.

  • Pry the volume button/left shoulder button connector off its socket on the motherboard with a spudger.

Aggiungi Commento

Using the flat end of a spudger, flip up the retaining flap on the ZIF connector for the D-pad/power button cable. With the pointed end of the spudger, pull the D-pad/power button cable from its connector on the motherboard.
  • Using the flat end of a spudger, flip up the retaining flap on the ZIF connector for the D-pad/power button cable.

  • With the pointed end of the spudger, pull the D-pad/power button cable from its connector on the motherboard.

Aggiungi Commento

Using the flat end of the spudger, carefully pry the battery cable out of its socket on the motherboard.
  • Using the flat end of the spudger, carefully pry the battery cable out of its socket on the motherboard.

    • Use caution, as the wires are very fragile and could come out of the connector if pulled on too hard.

Aggiungi Commento

Remove the seven 2.5 mm silver screws securing the power board to the upper case. Lift the power board off the upper case.
  • Remove the seven 2.5 mm silver screws securing the power board to the upper case.

  • Lift the power board off the upper case.

Aggiungi Commento

Lift the rubber pad off the back of the D-pad.
  • Lift the rubber pad off the back of the D-pad.

Aggiungi Commento

Open the display slightly, and push the D-pad up through the upper case. Lift the D-Pad from the handheld device.
  • Open the display slightly, and push the D-pad up through the upper case.

  • Lift the D-Pad from the handheld device.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 3 persone hanno completato questa guida.

Brett Hartt

Membro da: 12/04/2010

105.484 Reputazione

323 Guide realizzate

Team

iFixit Membro di iFixit

Community

114 Membri

5.902 Guide realizzate

Be very careful removing the screws - a Google search returns page after page of people who stripped their screws trying to remove the lower case or the power board. My lower case may be permanently attached now. If I did it over again, I would consider dripping a tiny amount of WD40 onto the screws and letting it seep in for a day before I tried removing them...

Nick Noble - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 3

Ultimi 30 Giorni: 21

Tutti i Tempi: 7,542