Introduzione

This guide provides shows you how to replace your LCD screenon your Nikon Coolpix 4100 with step-by-step instructions and photographs.

Tool on left - PH000 screwdriver
  • Tool on left - PH000 screwdriver

  • Tool on right - iPod fix-it tool

  • Soldering Iron

Aggiungi Commento

Locate the 3 black screws on the bottom of the camera and the 2 gray screws on each side of the camera. Remove them with a PH000 screwdriver.
  • Locate the 3 black screws on the bottom of the camera and the 2 gray screws on each side of the camera. Remove them with a PH000 screwdriver.

Aggiungi Commento

Locate the gray band that you removed the screws from; this holds the two halves of the camera together.  Use an iPod fix-it tool to pry the gray band loose and remove it. Locate the gray band that you removed the screws from; this holds the two halves of the camera together.  Use an iPod fix-it tool to pry the gray band loose and remove it.
  • Locate the gray band that you removed the screws from; this holds the two halves of the camera together. Use an iPod fix-it tool to pry the gray band loose and remove it.

Aggiungi Commento

Use the iPod fix-it tool to separate the back panel from the camera.
  • Use the iPod fix-it tool to separate the back panel from the camera.

Aggiungi Commento

Use the iPod fix-it tool to carefully pry the screen from the logic board.
  • Use the iPod fix-it tool to carefully pry the screen from the logic board.

  • There's a ribbon cable that connects the screen to the logic board.

Aggiungi Commento

This view shows the ribbon cable that connects to the screen.
  • This view shows the ribbon cable that connects to the screen.

Aggiungi Commento

Flip the screen down.  To disconnect the ribbon cable from the logic board, rock each end of the brown metal retainer that holds the ribbon cable in place until the ribbon disconnects.
  • Flip the screen down. To disconnect the ribbon cable from the logic board, rock each end of the brown metal retainer that holds the ribbon cable in place until the ribbon disconnects.

Aggiungi Commento

Remove the two screws on the top edge of the circuit board to the right of the viewfinder.
  • Remove the two screws on the top edge of the circuit board to the right of the viewfinder.

Aggiungi Commento

To connect the new screen, solder the wires in place and connect the ribbon cable to the logic board.
  • To connect the new screen, solder the wires in place and connect the ribbon cable to the logic board.

Aggiungi Commento

Unthread the four wires running across the top of the viewfinder from the plastic brackets holding them in place.
  • Unthread the four wires running across the top of the viewfinder from the plastic brackets holding them in place.

Aggiungi Commento

Remove the two black screws threaded vertically into the top of the viewfinder. Loosen the flash and circuit board for more accessibility.  This will allow for the viewfinder to be replaced.
  • Remove the two black screws threaded vertically into the top of the viewfinder. Loosen the flash and circuit board for more accessibility. This will allow for the viewfinder to be replaced.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Travis Buck

Membro da: 25/09/2012

107 Reputazione

2 Guide realizzate

Team

Ohio State, Team 1-2, Buehl Fall 2012 Membro di Ohio State, Team 1-2, Buehl Fall 2012

OSU-BUEHL-F12S1G2

3 Membri

3 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 2

Tutti i Tempi: 893