Salta al contenuto principale

Nerf N-Strike Elite Hail-Fire Right Shell Replacement

Cosa ti serve

  1. Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Left Shell: passo 1, immagine 1 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Left Shell: passo 1, immagine 2 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Left Shell: passo 1, immagine 3 di 3
    • Before disassembling your Nerf Hail-Fire, be sure to remove the batteries.

    • Remove the two 9.0 mm Phillips screws securing the battery compartment.

    • Slide the battery compartment out.

  2. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 2, immagine 1 di 1
    • Remove the five 9.0 mm Phillips screws securing the trigger.

  3. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 3, immagine 1 di 2 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 3, immagine 2 di 2
    • Remove the single 11.0 mm Phillips screw securing the magazine cartridge chambers.

    • Pull the entire chamber upwards to separate it from the rest of the Nerf Gun.

  4. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 4, immagine 1 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 4, immagine 2 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 4, immagine 3 di 3
    • Remove both halves of the ring by tugging on it upwards until the lock gets freed.

    • This requires quite a bit of force and if you are not careful, you may break the plastic lock.

  5. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 5, immagine 1 di 1
    • Remove the four 9.0 mm Phillips screws from the newly revealed cylinder.

  6. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 6, immagine 1 di 1
    • Remove the three 9.0 mm Phillips screws holding the top latch of the Nerf Gun together.

  7. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 7, immagine 1 di 1
    • Remove the three 9.0 mm Phillips screws holding together the firing chamber.

    • Remove the single 7.0 mm Phillips screw below the barrel.

    • Remove the two 14.0 mm Philips screws using a screwdriver with a length of approximately 4.0 inches and a diameter of approximately 0.2 cm.

  8. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 8, immagine 1 di 1
    • Remove the single 14.0 mm Phillips screw holding together the handle and the Nerf Gun.

  9. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 9, immagine 1 di 2 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 9, immagine 2 di 2
    • Remove the two 9.0 mm Phillips screws holding together the handle.

    • Remove the plastic cover of the handle.

  10. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 10, immagine 1 di 2 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 10, immagine 2 di 2
    • Insert one plastic opening tool inside one side of the orange part depicted in the picture.

    • Insert a second plastic opening tool to the other side of the orange part and gradually pull the piece out, freeing it from the handle.

  11. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 11, immagine 1 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 11, immagine 2 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 11, immagine 3 di 3
    • Pull one end of the handle away from the orange latch.

    • Repeat the procedure on the other side to completely remove the handle from the rest of the Nerf Gun.

  12. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 12, immagine 1 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 12, immagine 2 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 12, immagine 3 di 3
    • Lift the entire left shell slowly. The process should be easy and if there is any resistance, there is something wrong. You may have forgotten a screw.

    • Completely remove the left shell from the rest of the Nerf Gun.

  13. Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Inner Plastic Components: passo 13, immagine 1 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Inner Plastic Components: passo 13, immagine 2 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Inner Plastic Components: passo 13, immagine 3 di 3
    • Remove the cartridge support.

  14. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 14, immagine 1 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 14, immagine 2 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 14, immagine 3 di 3
    • Remove the handle crank.

  15. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 15, immagine 1 di 2 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 15, immagine 2 di 2
    • Remove the clear plastic barrel cover.

  16. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 16, immagine 1 di 2 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 16, immagine 2 di 2
    • Remove the firing pin.

  17. Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Right Shell: passo 17, immagine 1 di 2 Nerf N-Strike Elite Hail-Fire Right Shell Replacement, Right Shell: passo 17, immagine 2 di 2
    • Lift the trigger mechanism out of the shell.

    • You cannot fully remove the trigger mechanism just yet. However taking it out of the shell helps in later steps.

  18. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 18, immagine 1 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 18, immagine 2 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 18, immagine 3 di 3
    • Remove the two 9.0 mm Phillips screws.

  19. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 19, immagine 1 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 19, immagine 2 di 3 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 19, immagine 3 di 3
    • To remove the motor and trigger mechanism you have to detach these two wires which are glued to the shell.

    • Hold close to the wire and pull upward slowly.

    • If you pull too quickly you can potentially damage the wire.

  20. Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 20, immagine 1 di 2 Nerf N-Strike Elite Hail-Fire Right Shell Replacement: passo 20, immagine 2 di 2
    • Once all the pieces are removed the right shell should be fully accessible.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

sage

Membro da: 01/24/14

301 Reputazione

3 Guide realizzate

Team

Cal Poly, Team 13-13, Regan Winter 2014 Membro di Cal Poly, Team 13-13, Regan Winter 2014

CPSU-REGAN-W14S13G13

4 Membri

7 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 7

Tutti i Tempi: 4,515