Introduzione

Keep your aim sharp by replacing the motor.

Parti

Nessuna parte richiesta.

Before disassembling your Nerf Hail-Fire, be sure to remove the batteries. Remove the two 9.0 mm Phillips screws securing the battery compartment. Slide the battery compartment out.
  • Before disassembling your Nerf Hail-Fire, be sure to remove the batteries.

  • Remove the two 9.0 mm Phillips screws securing the battery compartment.

  • Slide the battery compartment out.

Aggiungi Commento

Remove the five 9.0 mm Phillips screws securing the trigger.
  • Remove the five 9.0 mm Phillips screws securing the trigger.

Aggiungi Commento

Remove the single 11.0 mm Phillips screw securing the magazine cartridge chambers. Pull the entire chamber upwards to separate it from the rest of the Nerf Gun.
  • Remove the single 11.0 mm Phillips screw securing the magazine cartridge chambers.

  • Pull the entire chamber upwards to separate it from the rest of the Nerf Gun.

Aggiungi Commento

Remove both halves of the ring by tugging on it upwards until the lock gets freed. This requires quite a bit of force and if you are not careful, you may break the plastic lock. This requires quite a bit of force and if you are not careful, you may break the plastic lock.
  • Remove both halves of the ring by tugging on it upwards until the lock gets freed.

  • This requires quite a bit of force and if you are not careful, you may break the plastic lock.

Aggiungi Commento

Remove the four 9.0 mm Phillips screws from the newly revealed cylinder.
  • Remove the four 9.0 mm Phillips screws from the newly revealed cylinder.

Aggiungi Commento

Remove the three 9.0 mm Phillips screws holding the top latch of the Nerf Gun together.
  • Remove the three 9.0 mm Phillips screws holding the top latch of the Nerf Gun together.

Aggiungi Commento

Remove the three 9.0 mm Phillips screws holding together the firing chamber.
  • Remove the three 9.0 mm Phillips screws holding together the firing chamber.

  • Remove the single 7.0 mm Phillips screw below the barrel.

  • Remove the two 14.0 mm Philips screws using a screwdriver with a length of approximately 4.0 inches and a diameter of approximately 0.2 cm.

Aggiungi Commento

Remove the single 14.0 mm Phillips screw holding together the handle and the Nerf Gun.
  • Remove the single 14.0 mm Phillips screw holding together the handle and the Nerf Gun.

Aggiungi Commento

Remove the two 9.0 mm Phillips screws holding together the handle. Remove the plastic cover of the handle.
  • Remove the two 9.0 mm Phillips screws holding together the handle.

  • Remove the plastic cover of the handle.

Aggiungi Commento

Insert one plastic opening tool inside one side of the orange part depicted in the picture. Insert a second plastic opening tool to the other side of the orange part and gradually pull the piece out, freeing it from the handle.
  • Insert one plastic opening tool inside one side of the orange part depicted in the picture.

  • Insert a second plastic opening tool to the other side of the orange part and gradually pull the piece out, freeing it from the handle.

Aggiungi Commento

Pull one end of the handle away from the orange latch. Repeat the procedure on the other side to completely remove the handle from the rest of the Nerf Gun. Repeat the procedure on the other side to completely remove the handle from the rest of the Nerf Gun.
  • Pull one end of the handle away from the orange latch.

  • Repeat the procedure on the other side to completely remove the handle from the rest of the Nerf Gun.

Aggiungi Commento

Lift the entire left shell slowly. The process should be easy and if there is any resistance, there is something wrong. You may have forgotten a screw. Completely remove the left shell from the rest of the Nerf Gun. Completely remove the left shell from the rest of the Nerf Gun.
  • Lift the entire left shell slowly. The process should be easy and if there is any resistance, there is something wrong. You may have forgotten a screw.

  • Completely remove the left shell from the rest of the Nerf Gun.

Aggiungi Commento

Remove the cartridge support. Remove the cartridge support. Remove the cartridge support.
  • Remove the cartridge support.

Aggiungi Commento

Remove the handle crank. Remove the handle crank. Remove the handle crank.
  • Remove the handle crank.

Aggiungi Commento

Remove the clear plastic barrel cover. Remove the clear plastic barrel cover.
  • Remove the clear plastic barrel cover.

Aggiungi Commento

Remove the firing pin. Remove the firing pin.
  • Remove the firing pin.

Aggiungi Commento

With your gun disassembled, locate the motor around the front portion of your gun as shown in Figure 1. Remove the two 9.0 mm Phillips screws securing the top shell of the motor casing. With your gun disassembled, locate the motor around the front portion of your gun as shown in Figure 1. Remove the two 9.0 mm Phillips screws securing the top shell of the motor casing. With your gun disassembled, locate the motor around the front portion of your gun as shown in Figure 1. Remove the two 9.0 mm Phillips screws securing the top shell of the motor casing.
  • With your gun disassembled, locate the motor around the front portion of your gun as shown in Figure 1. Remove the two 9.0 mm Phillips screws securing the top shell of the motor casing.

Aggiungi Commento

Remove the top shell of the motor casing. This should reveal the inner workings of the motor. Remove the top shell of the motor casing. This should reveal the inner workings of the motor.
  • Remove the top shell of the motor casing. This should reveal the inner workings of the motor.

Aggiungi Commento

With the shell now removed, locate the motor and controlling circuit board. With your index finger and thumb, squeeze the holders shown in Figure 2 and pull upwards to release the motor module from the rest of the motor's casing. Your motor should be detached from the casing, as shown in Figure 3. With the shell now removed, locate the motor and controlling circuit board. With your index finger and thumb, squeeze the holders shown in Figure 2 and pull upwards to release the motor module from the rest of the motor's casing. Your motor should be detached from the casing, as shown in Figure 3. With the shell now removed, locate the motor and controlling circuit board. With your index finger and thumb, squeeze the holders shown in Figure 2 and pull upwards to release the motor module from the rest of the motor's casing. Your motor should be detached from the casing, as shown in Figure 3.
  • With the shell now removed, locate the motor and controlling circuit board. With your index finger and thumb, squeeze the holders shown in Figure 2 and pull upwards to release the motor module from the rest of the motor's casing. Your motor should be detached from the casing, as shown in Figure 3.

Aggiungi Commento

Remove the wiring from the motor by disconnecting the wires from the circuit board.
  • Remove the wiring from the motor by disconnecting the wires from the circuit board.

So do you mean to cut the wires from their soldering place? B/c if that’s the case how do you fix/replace the motor? Thanks tho, this is great. For some reason one that I haven’t used really at all just stopped working after being in storage for a few years.

theflash3 - Replica

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 4 persone hanno completato questa guida.

Chris

Membro da: 24/01/2014

243 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 13-13, Regan Winter 2014 Membro di Cal Poly, Team 13-13, Regan Winter 2014

CPSU-REGAN-W14S13G13

4 Membri

7 Guide realizzate

Where do I get the motor from. I have a Nerf Demolisher 2 in 1 and I want to see if the place you buy it from has a motor for it.

Naman Singla - Replica

If you are still looking for the motors, you could check if any of these work with your model http://www.containmentcrew.com/product-c... . They are motors used often by people adding power to their motorized blasters, however, you may need a more powerful battery such as a LiPo or Nihm H.

AwesomeAtomicAustin (Nope) -

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 8

Ultimi 7 Giorni: 40

Ultimi 30 Giorni: 140

Tutti i Tempi: 7,305