Introduzione

Guide to installing a new camera.

Parti

Nessuna parte richiesta.

Press the panel release button on the top of the phone and simultaneously pull the rear panel away from the phone. Press the panel release button on the top of the phone and simultaneously pull the rear panel away from the phone.
  • Press the panel release button on the top of the phone and simultaneously pull the rear panel away from the phone.

Aggiungi Commento

Tilt the battery by lifting at the exposed notch. Slide the battery out of its casing.
  • Tilt the battery by lifting at the exposed notch.

  • Slide the battery out of its casing.

Aggiungi Commento

Use a T4 screwdriver to unscrew all six of the .216 inch screws that attach the housing to the case.
  • Use a T4 screwdriver to unscrew all six of the .216 inch screws that attach the housing to the case.

Aggiungi Commento

Use a plastic opening tool to lift the plastic casing. Pull the plastic casing directly away from the phone.
  • Use a plastic opening tool to lift the plastic casing.

  • Pull the plastic casing directly away from the phone.

Aggiungi Commento

Lift the black rubber loudspeaker housing up and out of the plastic casing.
  • Lift the black rubber loudspeaker housing up and out of the plastic casing.

Aggiungi Commento

Use a plastic opening tool to gently lift up the SIM card reader, located above the rubber antenna casing. You should hear a click as it releases. Caution: Remove carefully, if broken, the phone will not be able to make calls.
  • Use a plastic opening tool to gently lift up the SIM card reader, located above the rubber antenna casing. You should hear a click as it releases.

  • Caution: Remove carefully, if broken, the phone will not be able to make calls.

Aggiungi Commento

Use a plastic opening tool to pry the two ribbon cable connectors, unclipping them from their sockets on the motherboard. Caution: Remove carefully, if broken, the phone will not function properly.
  • Use a plastic opening tool to pry the two ribbon cable connectors, unclipping them from their sockets on the motherboard.

  • Caution: Remove carefully, if broken, the phone will not function properly.

Aggiungi Commento

Use a plastic opening tool to gently pry the motherboard up until you can tilt it with your fingers. Unhook it from the casing and slowly pull it out. Caution: Do this gently Unclipping too fast may cause damage to your phone.
  • Use a plastic opening tool to gently pry the motherboard up until you can tilt it with your fingers. Unhook it from the casing and slowly pull it out.

  • Caution: Do this gently Unclipping too fast may cause damage to your phone.

Aggiungi Commento

Turn the phone to the front.
  • Turn the phone to the front.

  • Push the keypad out through the plastic casing.

Aggiungi Commento

Turn the phone to the side.
  • Turn the phone to the side.

  • Thread the hinges of the slider through their holes in the casing and pull the slider down and away from the casing.

Aggiungi Commento

Slip the plastic opening tool carefully between the camera and the plastic casing.
  • Slip the plastic opening tool carefully between the camera and the plastic casing.

  • Gently pry the camera unit loose, being mindful of the adhesive that holds it in place and the copper colored ribbons that are attached to it.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Andrew Vu

Membro da: 07/10/2011

35 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 5-34, Amido Fall 2011 Membro di Cal Poly, Team 5-34, Amido Fall 2011

CPSU-AMIDO-F11S5G34

4 Membri

6 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 3

Tutti i Tempi: 512