Introduzione

Use this guide to replace the LCD Display on your Motorola Moto Q.

Use the Push Pin to remove the rubber screw covers by pushing the needle into the rubber and pulling up.
  • Use the Push Pin to remove the rubber screw covers by pushing the needle into the rubber and pulling up.

  • Be careful not to poke yourself when handling the push pin because it is very sharp.

Aggiungi Commento

Use the T6 screwdriver to remove the four screws holding the casing together.
  • Use the T6 screwdriver to remove the four screws holding the casing together.

  • Note: they are in the same place where you removed the four rubber coverings

Aggiungi Commento

Wedge the plastic opening tool in between the top and bottom cases. This may require a little or a lot of force so be careful. Note: the phone should be face up and the plastic opening tool should be face downwards
  • Wedge the plastic opening tool in between the top and bottom cases. This may require a little or a lot of force so be careful.

  • Note: the phone should be face up and the plastic opening tool should be face downwards

  • Once you get the plastic opening tool in, slide it across the side of the phone, making sure to keep the plastic opening tool wedged in between the two casings.

  • Repeat the 3 steps above for the top, bottom, and opposite side.

Aggiungi Commento

Gently lift and remove the back casing. Gently lift and remove the back casing.
  • Gently lift and remove the back casing.

Aggiungi Commento

MacBook Battery Fix Kits
Fix Kits Starting at $69.99
MacBook Battery Fix Kits
Starting at $69.99
Remove the plastic inner cover by placing the spudger under the left-most side and pry to the left and upwards. Gently rotate/wiggle the cover until you can pull it off the phone.
  • Remove the plastic inner cover by placing the spudger under the left-most side and pry to the left and upwards.

  • Gently rotate/wiggle the cover until you can pull it off the phone.

Aggiungi Commento

Using your fingers, remove the plastic piece that holds the camera in place. Using your fingers, remove the plastic piece that holds the camera in place.
  • Using your fingers, remove the plastic piece that holds the camera in place.

Aggiungi Commento

Carefully pry up the upper circuit board with the spudger. The second picture shows what your phone should look like when the upper circuit board is removed.
  • Carefully pry up the upper circuit board with the spudger.

  • The second picture shows what your phone should look like when the upper circuit board is removed.

Aggiungi Commento

Take out the camera and attached chip with the iPod removal tool.  Carefully pry the chip off its connection and the camera will come out too. Take out the camera and attached chip with the iPod removal tool.  Carefully pry the chip off its connection and the camera will come out too.
  • Take out the camera and attached chip with the iPod removal tool. Carefully pry the chip off its connection and the camera will come out too.

Aggiungi Commento

Remove the infra red plastic covering,the button on the left side of the phone, and the earphone cover lid by pulling straight up on them with your fingers. Wedge the plastic opening tool in between the logic board and the small orange band and gently pry upwards.
  • Remove the infra red plastic covering,the button on the left side of the phone, and the earphone cover lid by pulling straight up on them with your fingers.

  • Wedge the plastic opening tool in between the logic board and the small orange band and gently pry upwards.

  • Note: the orange band is connected to the logic board by a small connector.

Aggiungi Commento

Wedge the spudger in between the logic board and the front casing and gently lift while pulling away from the orange ribbon. Note: it is easier to remove the logic board by prying upwards near the top of left corner phone. Note: it is easier to remove the logic board by prying upwards near the top of left corner phone.
  • Wedge the spudger in between the logic board and the front casing and gently lift while pulling away from the orange ribbon.

  • Note: it is easier to remove the logic board by prying upwards near the top of left corner phone.

Aggiungi Commento

Wedge the plastic opening tool between the LCD screen and the metal casing holding it in and lift gently. Note: the LCD screen is also held in place by a silver tape. Simply pull the screen from one side to other to remove the screen completely. Note: the LCD screen is also held in place by a silver tape. Simply pull the screen from one side to other to remove the screen completely.
  • Wedge the plastic opening tool between the LCD screen and the metal casing holding it in and lift gently.

  • Note: the LCD screen is also held in place by a silver tape. Simply pull the screen from one side to other to remove the screen completely.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Luis Herrera

Membro da: 21/01/2010

52 Reputazione

4 Guide realizzate

Team

Cal Poly, Team 16-33, Maness Winter 2010 Membro di Cal Poly, Team 16-33, Maness Winter 2010

CPSU-MANESS-W10S16G33

4 Membri

5 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 3

Tutti i Tempi: 2,768