Introduzione

This guide will show you how to replace the motherboard, as yours may be malfunctioning. This is one of the longer processes so be patient. Tools are required. There are quite a few screws in this process so be sure to not lose any, and remember which ones came from where.

Slide the plastic case off of the back of the phone, exposing the battery. Slide the plastic case off of the back of the phone, exposing the battery. Slide the plastic case off of the back of the phone, exposing the battery.
  • Slide the plastic case off of the back of the phone, exposing the battery.

Aggiungi Commento

Pull up on the red battery release tab and pull the battery out of the phone. Pull up on the red battery release tab and pull the battery out of the phone. Pull up on the red battery release tab and pull the battery out of the phone.
  • Pull up on the red battery release tab and pull the battery out of the phone.

Aggiungi Commento

Remove the circled screws using a T-5 torques. These screws will be 4.3 millimeters in length. Be careful to not strip any screws.
  • Remove the circled screws using a T-5 torques. These screws will be 4.3 millimeters in length.

  • Be careful to not strip any screws.

Aggiungi Commento

Using a prying tool, snap off the front casing on the top and bottom of the phone. Using a prying tool, snap off the front casing on the top and bottom of the phone. Using a prying tool, snap off the front casing on the top and bottom of the phone.
  • Using a prying tool, snap off the front casing on the top and bottom of the phone.

Aggiungi Commento

Remove the circled screws using a T-5 torques.. These screws should be 5.8 millimeters in length. Remove the circled screws using a T-5 torques.. These screws should be 5.8 millimeters in length.
  • Remove the circled screws using a T-5 torques.. These screws should be 5.8 millimeters in length.

Aggiungi Commento

Using a plastic opening tool, snap open the phone. It should separate into a front piece with the hardware and a plastic backing. Using a plastic opening tool, snap open the phone. It should separate into a front piece with the hardware and a plastic backing. Using a plastic opening tool, snap open the phone. It should separate into a front piece with the hardware and a plastic backing.
  • Using a plastic opening tool, snap open the phone. It should separate into a front piece with the hardware and a plastic backing.

Aggiungi Commento

Using tweezers, remove the white wire at the top of the phone near the camera. Using tweezers, remove the white wire at the top of the phone near the camera. Using tweezers, remove the white wire at the top of the phone near the camera.
  • Using tweezers, remove the white wire at the top of the phone near the camera.

Aggiungi Commento

Remove these nine screws using a T-5 torques. These screws should be 2.40 mm in length Remove these nine screws using a T-5 torques. These screws should be 2.40 mm in length
  • Remove these nine screws using a T-5 torques. These screws should be 2.40 mm in length

Aggiungi Commento

Using tweezers, removed the white electrical tape on the motherboard. Using tweezers, removed the white electrical tape on the motherboard.
  • Using tweezers, removed the white electrical tape on the motherboard.

Aggiungi Commento

Using the plastic opening tool, lift up to remove the connector. Using the plastic opening tool, lift up to remove the connector.
  • Using the plastic opening tool, lift up to remove the connector.

Aggiungi Commento

Using a pry tool, lift the jawbone  connector. Using a pry tool, lift the jawbone  connector.
  • Using a pry tool, lift the jawbone connector.

Aggiungi Commento

Using tweezers, carefully disconnect the cable connector by pulling the cable out. Using tweezers, carefully disconnect the cable connector by pulling the cable out.
  • Using tweezers, carefully disconnect the cable connector by pulling the cable out.

Aggiungi Commento

Use a spudger to disconnect the cable connector. Use a spudger to disconnect the cable connector. Use a spudger to disconnect the cable connector.
  • Use a spudger to disconnect the cable connector.

Aggiungi Commento

Using a spudger, remove the camera. Lift up the motherboard and slide the spudger under the camera. Using a spudger, remove the camera. Lift up the motherboard and slide the spudger under the camera. Using a spudger, remove the camera. Lift up the motherboard and slide the spudger under the camera.
  • Using a spudger, remove the camera. Lift up the motherboard and slide the spudger under the camera.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Aaron Mak

Membro da: 29/10/2014

634 Reputazione

4 Guide realizzate

Team

UMass Dartmouth, Team 4-3, Miles Fall 2014 Membro di UMass Dartmouth, Team 4-3, Miles Fall 2014

UMASSD-MILES-F14S4G3

3 Membri

4 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 4

Tutti i Tempi: 515