Parti

Nessuna parte richiesta.

Place the phone with the screen facedown on a flat surface.
  • Place the phone with the screen facedown on a flat surface.

Aggiungi Commento

Pinch the latch upwards towards the top of the phone. Lift the back cover of the phone.
  • Pinch the latch upwards towards the top of the phone.

  • Lift the back cover of the phone.

  • There are tabs on the bottom end of the battery cover that the cover pivots about.

Aggiungi Commento

Remove the battery by pressing on the edge of the battery from the top of the phone towards the bottom and lifting up. Remove the battery by pressing on the edge of the battery from the top of the phone towards the bottom and lifting up.
  • Remove the battery by pressing on the edge of the battery from the top of the phone towards the bottom and lifting up.

Aggiungi Commento

Remove the four 8.5 mm screws from under the battery cover with a T4 Torx screwdriver.
  • Remove the four 8.5 mm screws from under the battery cover with a T4 Torx screwdriver.

  • Remove the two 8.5 mm screws from the top of the phone with a T4 Torx screwdriver.

Aggiungi Commento

Using the plastic pry tool remove the rear housing from the rest of the phone.  You may have to pry around all edges of the phone, not just the edge shown. When you remove the rear housing, the rubber cover for the headphone jack/charge port may fall out. If not, remove it.
  • Using the plastic pry tool remove the rear housing from the rest of the phone. You may have to pry around all edges of the phone, not just the edge shown.

  • When you remove the rear housing, the rubber cover for the headphone jack/charge port may fall out. If not, remove it.

Aggiungi Commento

Remove the small black circular rubber spacer. Remove the white rubber spacer.
  • Remove the small black circular rubber spacer.

  • Remove the white rubber spacer.

  • These pieces are small and easy to lose, especially the black one. Set them somewhere safe!

Aggiungi Commento

Gently remove the motherboard assembly from the front housing. Now, the front housing is free to be replaced, as well as the cosmetic keypad.
  • Gently remove the motherboard assembly from the front housing.

  • Now, the front housing is free to be replaced, as well as the cosmetic keypad.

Aggiungi Commento

Remove the 2 clips from the sides of the phone, just below the screen with the pry tool. Remove the 2 clips from the sides of the phone, just below the screen with the pry tool.
  • Remove the 2 clips from the sides of the phone, just below the screen with the pry tool.

Aggiungi Commento

The circuit board for the buttons is now free to be removed and replaced. The circuit board for the buttons is now free to be removed and replaced.
  • The circuit board for the buttons is now free to be removed and replaced.

Aggiungi Commento

Pry under the display screen, around each edge until it comes loose from the circuit board. You are removing the black plastic piece that holds the button circuit board. The piece has an aluminum frame around it. The two pieces will be removed together and don't need to be separated.
  • Pry under the display screen, around each edge until it comes loose from the circuit board.

    • You are removing the black plastic piece that holds the button circuit board. The piece has an aluminum frame around it. The two pieces will be removed together and don't need to be separated.

Aggiungi Commento

Gently remove the plastic and metal framework of the phone by lifting it up.
  • Gently remove the plastic and metal framework of the phone by lifting it up.

Aggiungi Commento

Use the prying tool to remove the connection between the display screen and the the main circuit board. The ribbon is not removed. It is instead connected to the circuit board by a set of circuit connectors.
  • Use the prying tool to remove the connection between the display screen and the the main circuit board.

    • The ribbon is not removed. It is instead connected to the circuit board by a set of circuit connectors.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Jason

Membro da: 23/10/2014

304 Reputazione

3 Guide realizzate

Team

Michigan Tech, Team 1-6, Lauer Fall 2014 Membro di Michigan Tech, Team 1-6, Lauer Fall 2014

MTU-LAUER-F14S1G6

3 Membri

6 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 2

Tutti i Tempi: 156