Parti

Nessuna parte richiesta.

Lay the computer down on its side as shown.
  • Lay the computer down on its side as shown.

  • Remove the two 14mm screws shown. The screws are loose enough to unscrew with your hands.

Aggiungi Commento

Gently slide the side panel straight back and remove from the computer.
  • Gently slide the side panel straight back and remove from the computer.

Aggiungi Commento

With your hands remove the 14mm screw that holds the cover on the back panel.
  • With your hands remove the 14mm screw that holds the cover on the back panel.

  • Gently pull the flap back to expose the T.V. Tuner screw.

Aggiungi Commento

Use the Phillips #2 to remove the 8mm screw that holds the T.V. Tuner in place.
  • Use the Phillips #2 to remove the 8mm screw that holds the T.V. Tuner in place.

Aggiungi Commento

With moderate force, pull straight up on the chip to remove it from the computer.
  • With moderate force, pull straight up on the chip to remove it from the computer.

Aggiungi Commento

Push down on the white clips on both sides of the memory module to release it.
  • Push down on the white clips on both sides of the memory module to release it.

  • Gently pull up on the memory module to remove it from the unit.

Aggiungi Commento

Using the Phillips #00 Precision screwdriver, unscrew the four 12mm screws that hold the fan in place.
  • Using the Phillips #00 Precision screwdriver, unscrew the four 12mm screws that hold the fan in place.

  • Be careful not to strip the screws.

Fan does not need to be removed from the heat sink.

Ken - Replica

Unplug the fan from the motherboard by gently pulling out the single plug. Then lift the fan up and out of the computer.
  • Unplug the fan from the motherboard by gently pulling out the single plug. Then lift the fan up and out of the computer.

Aggiungi Commento

Loosen the four screws that hold the heat sink in place using a Phillips #2 screwdriver.
  • Loosen the four screws that hold the heat sink in place using a Phillips #2 screwdriver.

  • The screws do not come all the way out of the heat sink

  • Pull the heat sink straight up to remove it.

Loosen these four screws with the fan attached. Unplug the fan from the motherboard and remove the heat sink / fan as one component.

Ken - Replica

Remove the 2 8mm screws holding the CPU cover using a Torx #20 screwdriver. Remove the 11 mm screw using a Torx #20 screwdriver.
  • Remove the 2 8mm screws holding the CPU cover using a Torx #20 screwdriver.

  • Remove the 11 mm screw using a Torx #20 screwdriver.

  • Remove the cover and remove the CPU by gently pulling upward.

Why not just lift the lever that allows the CPU cover to open to gain access to the CPU? Removing the cover is not necessary.

Ken - Replica

Unplug all cords attached to the motherboard. The largest connection requires a significant amount of force to be removed. The largest connection requires a significant amount of force to be removed.
  • Unplug all cords attached to the motherboard.

  • The largest connection requires a significant amount of force to be removed.

Aggiungi Commento

Remove all 6 8mm screws attaching the motherboard to the base of the tower using a Phillips #2 screwdriver. Gently pull the motherboard from the unit.
  • Remove all 6 8mm screws attaching the motherboard to the base of the tower using a Phillips #2 screwdriver.

  • Gently pull the motherboard from the unit.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 4 persone hanno completato questa guida.

Timothy Grebe

Membro da: 19/10/2014

1.304 Reputazione

9 Guide realizzate

Team

Cal Poly, Team 10-39, Amido Fall 2014 Membro di Cal Poly, Team 10-39, Amido Fall 2014

CPSU-AMIDO-F14S10G39

4 Membri

9 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 10

Ultimi 30 Giorni: 44

Tutti i Tempi: 2,303