Introduzione

If the audio on the phone isn't working, you may want to try replacing the speaker.

Parti

Nessuna parte richiesta.

Turn the phone over so the back side is facing you.
  • Turn the phone over so the back side is facing you.

Aggiungi Commento

Placing your thumb on the bottom of the phone, apply pressure to the small ridge in the middle of the phone and push upward towards the camera. The back casing should slide off.
  • Placing your thumb on the bottom of the phone, apply pressure to the small ridge in the middle of the phone and push upward towards the camera.

  • The back casing should slide off.

Aggiungi Commento

Using your index finger, pull the top of the battery out first. Place your finger at the top center of the battery in the gap that is provided. Then pull the battery towards yourself. The battery should easily fall out after the top of the battery has been pulled out.
  • Using your index finger, pull the top of the battery out first. Place your finger at the top center of the battery in the gap that is provided. Then pull the battery towards yourself.

  • The battery should easily fall out after the top of the battery has been pulled out.

Aggiungi Commento

Unscrew the six 2.4mm Phillips #00 screws (three on the left and three on the right of the phone) to remove the inner back case. Unscrew the six 2.4mm Phillips #00 screws (three on the left and three on the right of the phone) to remove the inner back case.
  • Unscrew the six 2.4mm Phillips #00 screws (three on the left and three on the right of the phone) to remove the inner back case.

Aggiungi Commento

Once all six screws are removed, use the plastic opening tool to carefully pry apart the inner back case. Push the plastic tool underneath the case. Carefully push upward, with the tool, while moving it around the case.
  • Once all six screws are removed, use the plastic opening tool to carefully pry apart the inner back case. Push the plastic tool underneath the case. Carefully push upward, with the tool, while moving it around the case.

Aggiungi Commento

Remove the camera, lock, and volume buttons from the side of the phone. Remove the camera, lock, and volume buttons from the side of the phone.
  • Remove the camera, lock, and volume buttons from the side of the phone.

Aggiungi Commento

Carefully remove the two  3mm Phillips #00 screws (one on the top and one on the bottom) that are attaching the motherboard to the phone. Carefully remove the two  3mm Phillips #00 screws (one on the top and one on the bottom) that are attaching the motherboard to the phone.
  • Carefully remove the two 3mm Phillips #00 screws (one on the top and one on the bottom) that are attaching the motherboard to the phone.

Aggiungi Commento

Kit RAM Mac
Accelera il Mac. Porta la memoria al massimo.
Kit RAM Mac
Metti più memoria nel tuo Mac.
For this next step, carefully lift and remove the motherboard. A connector cable will still be connected to the motherboard upon removing it.
  • For this next step, carefully lift and remove the motherboard.

    • A connector cable will still be connected to the motherboard upon removing it.

    • Damage to the connector cable will permanently disable phone.

Aggiungi Commento

Carefully unclip the silver metallic tab from the motherboard. Carefully unclip the silver metallic tab from the motherboard.
  • Carefully unclip the silver metallic tab from the motherboard.

Aggiungi Commento

Once the cable is removed, you have successfully disassembled the motherboard of your phone. Once the cable is removed, you have successfully disassembled the motherboard of your phone.
  • Once the cable is removed, you have successfully disassembled the motherboard of your phone.

Aggiungi Commento

Turn the motherboard over and carefully remove the keypad from the motherboard.
  • Turn the motherboard over and carefully remove the keypad from the motherboard.

  • The keyboard may be sitting loosely in the case (not attached to the motherboard). Carefully remove keyboard from case.

Aggiungi Commento

After removing the motherboard and keyboard, unscrew eight 1.6mm Phillips #00 screws in the middle of the phone.
  • After removing the motherboard and keyboard, unscrew eight 1.6mm Phillips #00 screws in the middle of the phone.

Aggiungi Commento

Remove slider piece.
  • Remove slider piece.

    • Pay close attention that you don’t lose the spring.

    • Carefully remove the spring.

Aggiungi Commento

Remove six 2.25mm Phillips #00 screws along the outside of the case. Remove six 2.25mm Phillips #00 screws along the outside of the case.
  • Remove six 2.25mm Phillips #00 screws along the outside of the case.

Aggiungi Commento

Using the plastic opening tool, carefully open and remove the case. Slide the tool along the edge and pry upwards to open. Using the plastic opening tool, carefully open and remove the case. Slide the tool along the edge and pry upwards to open.
  • Using the plastic opening tool, carefully open and remove the case. Slide the tool along the edge and pry upwards to open.

Aggiungi Commento

Remove the black electrical tape holding the LCD to the screen.
  • Remove the black electrical tape holding the LCD to the screen.

Aggiungi Commento

Un-clasp the small tab in the top right corner.
  • Un-clasp the small tab in the top right corner.

Aggiungi Commento

Unhook the LCD from tabs on the bottom using the plastic opening tool. Remove the LCD. Be careful, the LCD screen is fragile. Remove the LCD. Be careful, the LCD screen is fragile.
  • Unhook the LCD from tabs on the bottom using the plastic opening tool.

  • Remove the LCD. Be careful, the LCD screen is fragile.

Aggiungi Commento

The speaker is attached to the top of the LCD. The speaker is attached to the top of the LCD.
  • The speaker is attached to the top of the LCD.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Micaela Saqui

Membro da: 19/04/2012

39 Reputazione

14 Guide realizzate

Team

Cal Poly, Team 9-41, Regan Spring 2012 Membro di Cal Poly, Team 9-41, Regan Spring 2012

CPSU-REGAN-S12S9G41

5 Membri

16 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 736