Introduzione

Steps to remove LG VX8550 slider mechanism

Slide the battery release up.
  • Slide the battery release up.

Aggiungi Commento

Remove the battery by lifting away from the case.
  • Remove the battery by lifting away from the case.

Aggiungi Commento

Remove the 2 screw covers next to the rear speaker with a Push Pin.
  • Remove the 2 screw covers next to the rear speaker with a Push Pin.

Aggiungi Commento

Remove the 4 cover screws with a Philips #00 screwdriver.
  • Remove the 4 cover screws with a Philips #00 screwdriver.

Aggiungi Commento

Use the iPod opening tool to pry off the back casing.
  • Use the iPod opening tool to pry off the back casing.

Aggiungi Commento

Continue sliding the iPod opening tool around the seam of the casing to separate the front and back casings.
  • Continue sliding the iPod opening tool around the seam of the casing to separate the front and back casings.

Aggiungi Commento

Separate the casing halves.
  • Separate the casing halves.

  • Be sure to keep track of the side buttons as they fall out.

Aggiungi Commento

Remove the 2 screws from the back of the phone with a Phillips #00 Screwdriver.
  • Remove the 2 screws from the back of the phone with a Phillips #00 Screwdriver.

Aggiungi Commento

Carefully lift up on the motherboard to see the ribbon cables underneath.
  • Carefully lift up on the motherboard to see the ribbon cables underneath.

  • Use the spudger to carefully disconnect the ribbon cable from the motherboard.

Aggiungi Commento

Remove the motherboard from the front casing by lifting straight up.
  • Remove the motherboard from the front casing by lifting straight up.

Aggiungi Commento

Lay the phone with the screen facedown.
  • Lay the phone with the screen facedown.

  • The 6 slider screws are visible.

Aggiungi Commento

Peel back but don't remove the blue tape to access the 2 center screws.
  • Peel back but don't remove the blue tape to access the 2 center screws.

  • Remove the 6 slider screws with the Phillips #00 screwdriver.

Aggiungi Commento

Lift the keypad housing away from the slider.
  • Lift the keypad housing away from the slider.

Aggiungi Commento

Remove the 2 screw covers next to the speaker with a push pin next to the camera.
  • Remove the 2 screw covers next to the speaker with a push pin next to the camera.

Aggiungi Commento

Remove the 6 screws with a Phillips #00 Screwdriver.
  • Remove the 6 screws with a Phillips #00 Screwdriver.

Aggiungi Commento

Use the ipod opening tool to pry the screen casing and the slider mechanism apart from each other.
  • Use the ipod opening tool to pry the screen casing and the slider mechanism apart from each other.

Aggiungi Commento

Carefully lift the slider mechanism to see the ribbon cables underneath.
  • Carefully lift the slider mechanism to see the ribbon cables underneath.

Aggiungi Commento

Slide ribbon cable through the slider mechanism.
  • Slide ribbon cable through the slider mechanism.

Aggiungi Commento

Separate the two halves.
  • Separate the two halves.

Aggiungi Commento

With the slider mechanism separated from the screen casing the 8 screws securing the slider mechanism are visible.
  • With the slider mechanism separated from the screen casing the 8 screws securing the slider mechanism are visible.

  • Remove the 8 screws.

Aggiungi Commento

Remove slider mechanism.  Now is a good time to clean slider mechanism if sticky.
  • Remove slider mechanism. Now is a good time to clean slider mechanism if sticky.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Nathan Jones

Membro da: 10/04/2010

83 Reputazione

20 Guide realizzate

Team

Cal Poly, Team 34-55, Forte Spring 2010 Membro di Cal Poly, Team 34-55, Forte Spring 2010

CPSU-FORTE-S10S34G55

5 Membri

20 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 2,993