Remove the back cover by placing your fingernail in the crease between the cover and the charging port.
  • Remove the back cover by placing your fingernail in the crease between the cover and the charging port.

  • Pry upward and the cover should pop off easily

Aggiungi Commento

Remove the battery from the battery bay by prying with your finger at the groove on the lower end of the battery bay.
  • Remove the battery from the battery bay by prying with your finger at the groove on the lower end of the battery bay.

Aggiungi Commento

Locate 10 screws and remove each one using a screw driver Locate 10 screws and remove each one using a screw driver
  • Locate 10 screws and remove each one using a screw driver

Aggiungi Commento

Use a plastic opening tool to pry away the cover by placing it between the cover and the screen bezel.
  • Use a plastic opening tool to pry away the cover by placing it between the cover and the screen bezel.

  • Pry all the way around the phone about every centimeter until the cover is completely separated from the phone.

Aggiungi Commento

Locate the rear facing camera. Pry the ribbon cable off of it's connector using the plastic spudger tool. Use your finger to remove the camera.
  • Locate the rear facing camera.

  • Pry the ribbon cable off of it's connector using the plastic spudger tool.

  • Use your finger to remove the camera.

Aggiungi Commento

Locate the front facing camera. Pry the ribbon cable off of it's connector using the plastic spudger tool. Use your finger to remove the camera.
  • Locate the front facing camera.

  • Pry the ribbon cable off of it's connector using the plastic spudger tool.

  • Use your finger to remove the camera.

Aggiungi Commento

Use the plastic spudger tool or a flat head screwdriver to pry the ribbon cables off of their connectors. Use the plastic spudger tool or a flat head screwdriver to pry the ribbon cables off of their connectors. Use the plastic spudger tool or a flat head screwdriver to pry the ribbon cables off of their connectors.
  • Use the plastic spudger tool or a flat head screwdriver to pry the ribbon cables off of their connectors.

Aggiungi Commento

Use your finger to lift the motherboard from the edge and remove it from the phone.
  • Use your finger to lift the motherboard from the edge and remove it from the phone.

Aggiungi Commento

Pull from the tabs on the edges of the security tape. This piece is not absolutely necessary to replace when putting the phone back together, but it secures the cables against movement from day to day activities. If you have some electrical tape lying around, use it to secure the cables during the process of putting the phone back together.
  • Pull from the tabs on the edges of the security tape.

  • This piece is not absolutely necessary to replace when putting the phone back together, but it secures the cables against movement from day to day activities. If you have some electrical tape lying around, use it to secure the cables during the process of putting the phone back together.

Aggiungi Commento

Peel the LCD cable off of the phone. Peel the LCD cable off of the phone.
  • Peel the LCD cable off of the phone.

Aggiungi Commento

Use a heat gun to heat the edges of the LCD screen and melt the adhesive that holds the glass on. Pry the edges of the glass away from the phone using a plastic spudger tool. Do this quickly before the glass cools down and starts to stick again.
  • Use a heat gun to heat the edges of the LCD screen and melt the adhesive that holds the glass on.

  • Pry the edges of the glass away from the phone using a plastic spudger tool. Do this quickly before the glass cools down and starts to stick again.

  • The glass will get very hot. Take care not to burn yourself when touching it.

Aggiungi Commento

Push the ribbon cable connected to the Digitizer through the hole in the case and then pull the glass screen away from the phone. Push the ribbon cable connected to the Digitizer through the hole in the case and then pull the glass screen away from the phone. Push the ribbon cable connected to the Digitizer through the hole in the case and then pull the glass screen away from the phone.
  • Push the ribbon cable connected to the Digitizer through the hole in the case and then pull the glass screen away from the phone.

Aggiungi Commento

Push the ribbon cable connected to the LCD screen through the hole in the case. Pull the LCD screen away from the case. At this point you are ready to replace the LCD with a working one.
  • Push the ribbon cable connected to the LCD screen through the hole in the case.

  • Pull the LCD screen away from the case.

  • At this point you are ready to replace the LCD with a working one.

Aggiungi Commento

If you bought a full LCD and Digitizer assembly, then you can discard the old Digitizer and just replace it with the new one. If you only bought the LCD component and would like to reuse the current digitizer then follow the steps below. Peel off the excess adhesive from the bezel of the glass screen.
  • If you bought a full LCD and Digitizer assembly, then you can discard the old Digitizer and just replace it with the new one. If you only bought the LCD component and would like to reuse the current digitizer then follow the steps below.

  • Peel off the excess adhesive from the bezel of the glass screen.

  • Line the bezel of the glass screen with 3M double sided adhesive tape. You will be able to stick it back on easily.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 14 persone hanno completato questa guida.

Team

UMass Dartmouth, Team 1-9, Shastany Fall 2014 Membro di UMass Dartmouth, Team 1-9, Shastany Fall 2014

UMASSD-SHASTANY-F14S1G9

3 Membri

5 Guide realizzate

It is possible to change only digitizer? It seems glued or fused to LCD by a whole surface...

kapr73 - Replica

yes, it is glued and can be removed by heat

Elliott -

Great article, I could change my digitizer successfully.

Respect.

Fran Hdez - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 22

Ultimi 30 Giorni: 85

Tutti i Tempi: 10,865