Introduzione

This will show a step-by-step process in replacing the camera's mic.

Parti

Nessuna parte richiesta.

Open the battery cover.
  • Open the battery cover.

Aggiungi Commento

Slide the orange latch sideways to eject the battery.
  • Slide the orange latch sideways to eject the battery.

  • Remove the battery.

Aggiungi Commento

Remove 7 screws. 1 (6.25 mm) screw located on the top right corner, next to the view screen. 4 (4.45mm) screws on the bottom of the camera.
  • Remove 7 screws.

    • 1 (6.25 mm) screw located on the top right corner, next to the view screen.

    • 4 (4.45mm) screws on the bottom of the camera.

    • 2 (2.95mm) screws on the left side of the camera.

Aggiungi Commento

There will be 2 (5.39mm) screws. Remove the screws in order to remove the lanyard. There will be 2 (5.39mm) screws. Remove the screws in order to remove the lanyard. There will be 2 (5.39mm) screws. Remove the screws in order to remove the lanyard.
  • There will be 2 (5.39mm) screws. Remove the screws in order to remove the lanyard.

Aggiungi Commento

Remove the rear camera casing. Remove the front casing.
  • Remove the rear camera casing.

  • Remove the front casing.

Aggiungi Commento

Remove the top panel screw (1x 4.37mm). Remove the top panel screw (1x 4.37mm).
  • Remove the top panel screw (1x 4.37mm).

Aggiungi Commento

Remove the top panel. Remove the top panel.
  • Remove the top panel.

Aggiungi Commento

Remove the back panel screws (1x 3.33mm, and  1x 3.40mm). Remove the back panel screws (1x 3.33mm, and  1x 3.40mm).
  • Remove the back panel screws (1x 3.33mm, and 1x 3.40mm).

Aggiungi Commento

Separate the inner casing  from the tripod mount. Separate the inner casing  from the tripod mount. Separate the inner casing  from the tripod mount.
  • Separate the inner casing from the tripod mount.

Aggiungi Commento

Gently pull the  orange tab out of the  circuit board. Gently pull the  orange tab out of the  circuit board. Gently pull the  orange tab out of the  circuit board.
  • Gently pull the orange tab out of the circuit board.

Aggiungi Commento

Carefully flip the LCD panel to expose the central circuit board. Carefully flip the LCD panel to expose the central circuit board.
  • Carefully flip the LCD panel to expose the central circuit board.

Aggiungi Commento

Remove the (1x 3.33mm) screw from the menu button panel .
  • Remove the (1x 3.33mm) screw from the menu button panel .

Aggiungi Commento

Pull the second orange tab from the circuit board and remove the buttons. Pull the second orange tab from the circuit board and remove the buttons.
  • Pull the second orange tab from the circuit board and remove the buttons.

Aggiungi Commento

Flip up the LCD screen to reveal the two orange ribbon cables. Disconnect the two ribbons cables from their sockets on the motherboard. Disconnect the two ribbons cables from their sockets on the motherboard.
  • Flip up the LCD screen to reveal the two orange ribbon cables.

  • Disconnect the two ribbons cables from their sockets on the motherboard.

Aggiungi Commento

Locate the microphone on top of the camera
  • Locate the microphone on top of the camera

Aggiungi Commento

With a pry bar, remove microphone away from camera carefully.
  • With a pry bar, remove microphone away from camera carefully.

Aggiungi Commento

Release it from it's pin and desolder
  • Release it from it's pin and desolder

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Odessa

Membro da: 24/06/2010

55 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 2-8, Johann Summer 2010 Membro di Cal Poly, Team 2-8, Johann Summer 2010

CPSU-JOHANN-R10S2G8

5 Membri

8 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 2

Tutti i Tempi: 1,801