Introduzione

This guide will teach you how to take apart your phone so that you can remove/replace the screen.

Power the phone off. Use your thumb to gently press downward and away from the camera to remove the battery cover.
  • Power the phone off.

  • Use your thumb to gently press downward and away from the camera to remove the battery cover.

Aggiungi Commento

Pull on the plastic tab to release the battery. Pull on the plastic tab to release the battery.
  • Pull on the plastic tab to release the battery.

Aggiungi Commento

Use a plastic opening tool to remove the camera cover. Work around the corners to avoid breaking the plastic clips that hold the camera cover on.
  • Use a plastic opening tool to remove the camera cover.

  • Work around the corners to avoid breaking the plastic clips that hold the camera cover on.

  • Lift the camera cover off of the phone.

Aggiungi Commento

Remove the stylus from the phone.
  • Remove the stylus from the phone.

  • Remove the four 5.5 mm screws with the T6 Torx Screwdriver.

  • One of the screws might be under a sticker, which will void your warranty.

Aggiungi Commento

Be Careful! Do not insert the spudger in between the keyboard and screen.  This could break the keyboard off the phone. If your phone contains a memory card, you may want to remove it before proceeding with this step. Insert spudger in the bottom corner as seen in the picture.  Carefully slide the spudger from the bottom towards the top as seen in the second picture.
  • Be Careful! Do not insert the spudger in between the keyboard and screen. This could break the keyboard off the phone.

  • If your phone contains a memory card, you may want to remove it before proceeding with this step.

  • Insert spudger in the bottom corner as seen in the picture. Carefully slide the spudger from the bottom towards the top as seen in the second picture.

  • Lift the back case off completely.

  • The speakers might be dangling and unsecured.

Aggiungi Commento

Grip the speaker connector with your thumb and finger and gently pull up. Repeat for 2nd speaker.
  • Grip the speaker connector with your thumb and finger and gently pull up.

  • Repeat for 2nd speaker.

Aggiungi Commento

Locate the camera and pry off with the plastic opening tool or spudger.
  • Locate the camera and pry off with the plastic opening tool or spudger.

Aggiungi Commento

Remove the 3.4 mm black screw with the Phillips #000 screwdriver.
  • Remove the 3.4 mm black screw with the Phillips #000 screwdriver.

Aggiungi Commento

Remove the plastic tape to reveal the connector. Use your finger or plastic opening tool to flip the connector and release the cable.
  • Remove the plastic tape to reveal the connector.

  • Use your finger or plastic opening tool to flip the connector and release the cable.

Aggiungi Commento

Use the plastic opening tool to carefully lift the motherboard off one corner at a time. Lift the motherboard slowly away from the keyboard because there is a cable attached to bottom of the motherboard.
  • Use the plastic opening tool to carefully lift the motherboard off one corner at a time.

  • Lift the motherboard slowly away from the keyboard because there is a cable attached to bottom of the motherboard.

  • If the motherboard is not easily removed by pulling, then lift one side of the motherboard until you can see the attached cable. Then use the plastic opening tool to detach the cable from the motherboard.

Aggiungi Commento

Using the Phillips Screwdriver #000 remove the four 3.3 mm screws. Carefully lift the keyboard from the plastic plate by allowing the ribbon cable to slip through the opening of the plastic plate.
  • Using the Phillips Screwdriver #000 remove the four 3.3 mm screws.

  • Carefully lift the keyboard from the plastic plate by allowing the ribbon cable to slip through the opening of the plastic plate.

Aggiungi Commento

Use the Phillips Screwdriver #000 to remove the four 3.8 mm screws from the back of the screen.
  • Use the Phillips Screwdriver #000 to remove the four 3.8 mm screws from the back of the screen.

Aggiungi Commento

Insert the spudger between the panel and the case. Gently pry off the panel by rotating or wiggling the spudger back and forth. Lift the panel off while allowing the ribbon to slip through the opening.
  • Insert the spudger between the panel and the case.

  • Gently pry off the panel by rotating or wiggling the spudger back and forth.

  • Lift the panel off while allowing the ribbon to slip through the opening.

Aggiungi Commento

Remove the four 2.9 mm screws with the Phillips Screwdriver #000. Use your fingers to separate the screen assembly from the front panel. Use your fingers to separate the screen assembly from the front panel.
  • Remove the four 2.9 mm screws with the Phillips Screwdriver #000.

  • Use your fingers to separate the screen assembly from the front panel.

Aggiungi Commento

Insert the spudger between the green panel and the screen itself. Gently wiggle the spudger to pry them apart.
  • Insert the spudger between the green panel and the screen itself.

  • Gently wiggle the spudger to pry them apart.

Aggiungi Commento

Remove the tape. Locate the connecting ribbon. Using the spudger or your thumb and finger, flip the switch up and disconnect the ribbon.
  • Remove the tape.

  • Locate the connecting ribbon.

  • Using the spudger or your thumb and finger, flip the switch up and disconnect the ribbon.

  • Lift off the panel from the screen.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Taylor Stone

Membro da: 06/10/2011

45 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 20-28, Maness Fall 2011 Membro di Cal Poly, Team 20-28, Maness Fall 2011

CPSU-MANESS-F11S20G28

4 Membri

7 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 1

Tutti i Tempi: 862