Introduzione

Use this guide to replace a broken or damaged camera.

Insert the plastic opening tool into the top of the Thunderbolt near the power button.
  • Insert the plastic opening tool into the top of the Thunderbolt near the power button.

  • Gently pry up on the rear panel around the edges until it is loose.

Aggiungi Commento

Lift and remove the rear panel.
  • Lift and remove the rear panel.

Aggiungi Commento

Using the plastic opening tool, lift up the battery from the bottom near the kickstand. Remove the battery from the inner frame.
  • Using the plastic opening tool, lift up the battery from the bottom near the kickstand.

  • Remove the battery from the inner frame.

Aggiungi Commento

Remove the six Phillips screws from the perimeter of the rear frame.
  • Remove the six Phillips screws from the perimeter of the rear frame.

  • By removing the screw with the "void" sticker on it, your Thunderbolt will no longer be covered under warranty.

Aggiungi Commento

Insert the plastic opening tool into the bottom of the phone underneath the soft keys. Gently pry up on the plastic cover by sliding the plastic opening tool across the bottom of the phone.
  • Insert the plastic opening tool into the bottom of the phone underneath the soft keys.

  • Gently pry up on the plastic cover by sliding the plastic opening tool across the bottom of the phone.

  • Remove the plastic cover.

  • The plastic cover will have adhesive on it making it difficult to remove.

Aggiungi Commento

Remove the two Phillips screws where the plastic cover was.
  • Remove the two Phillips screws where the plastic cover was.

Aggiungi Commento

Insert the plastic opening tool in between the screen and the frame on the side of the phone. Slowly slide the the plastic opening tool along the side of the phone until the screen begins to separate from the frame.
  • Insert the plastic opening tool in between the screen and the frame on the side of the phone.

  • Slowly slide the the plastic opening tool along the side of the phone until the screen begins to separate from the frame.

  • Do the same for the opposite side of the phone.

Aggiungi Commento

Carefully separate the screen and phone from the rear frame, starting from the bottom. Gently pull down on the phone and screen to fully separate it from the rear frame. Gently pull down on the phone and screen to fully separate it from the rear frame.
  • Carefully separate the screen and phone from the rear frame, starting from the bottom.

  • Gently pull down on the phone and screen to fully separate it from the rear frame.

Aggiungi Commento

Remove the two Phillips screws securing rear inner frame to device.
  • Remove the two Phillips screws securing rear inner frame to device.

Aggiungi Commento

Insert the plastic opening tool between the rear inner frame and the motherboard and slowly work your way around the device.
  • Insert the plastic opening tool between the rear inner frame and the motherboard and slowly work your way around the device.

Aggiungi Commento

Remove the rear inner frame from the rest of the device. Remove the rear inner frame from the rest of the device.
  • Remove the rear inner frame from the rest of the device.

Aggiungi Commento

Using the tip of an plastic opening tool flip up the tab holding the capacitive button ribbon cable. Be careful opening these tabs as they are very easy to break.
  • Using the tip of an plastic opening tool flip up the tab holding the capacitive button ribbon cable.

  • Be careful opening these tabs as they are very easy to break.

  • Use a pair of tweezers to pull the capacitive button cable out of its socket.

Aggiungi Commento

Lifting from the side where the ribbon was disconnected, flip over the motherboard. Remove the black tape covering the tabs connecting the motherboard and LCD.
  • Lifting from the side where the ribbon was disconnected, flip over the motherboard.

  • Remove the black tape covering the tabs connecting the motherboard and LCD.

Aggiungi Commento

Using the plastic opening tool pop up  the two tabs connecting the LCD and motherboard.
  • Using the plastic opening tool pop up the two tabs connecting the LCD and motherboard.

Aggiungi Commento

Once the tabs have been popped up, slowly pull the two pieces away from each other. If there is resistance pulling apart the phone then a ribbon or tab has not been disconnected properly/completely.
  • Once the tabs have been popped up, slowly pull the two pieces away from each other.

  • If there is resistance pulling apart the phone then a ribbon or tab has not been disconnected properly/completely.

Aggiungi Commento

The motherboard should now be completely disconnected
  • The motherboard should now be completely disconnected

Aggiungi Commento

Use a finger nail to get in between the tape and the phone, then pull the tape off gently. Use a finger nail to get in between the tape and the phone, then pull the tape off gently.
  • Use a finger nail to get in between the tape and the phone, then pull the tape off gently.

Aggiungi Commento

Pop up the tab connecting the camera to the motherboard.
  • Pop up the tab connecting the camera to the motherboard.

Aggiungi Commento

Flip over motherboard and using tweezers gently grab the camera, then pull back and up.
  • Flip over motherboard and using tweezers gently grab the camera, then pull back and up.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Vanessa

Membro da: 18/01/2013

60 Reputazione

4 Guide realizzate

Team

Cal Poly, Team 19-45, Regan Winter 2013 Membro di Cal Poly, Team 19-45, Regan Winter 2013

CPSU-REGAN-W13S19G45

4 Membri

12 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 831