Introduzione

Be careful with the LCD screen. It is fragile.

First remove the back cover of your phone to expose the battery.
  • First remove the back cover of your phone to expose the battery.

Aggiungi Commento

Turn the phone over and remove the battery by using your thumb to push forward on the battery and then lift it.
  • Turn the phone over and remove the battery by using your thumb to push forward on the battery and then lift it.

Aggiungi Commento

Take the battery out When reassembling, make sure that the battery contacts match up.
  • Take the battery out

  • When reassembling, make sure that the battery contacts match up.

Aggiungi Commento

Remove the four 4.9mm T6 Torx screws that secure the back panel to the rest of the phone Remove the four 4.9mm T6 Torx screws that secure the back panel to the rest of the phone
  • Remove the four 4.9mm T6 Torx screws that secure the back panel to the rest of the phone

Aggiungi Commento

Remove the two 4.3mm #00 Phillips screws that secure the back panel to the rest of the phone
  • Remove the two 4.3mm #00 Phillips screws that secure the back panel to the rest of the phone

Aggiungi Commento

Use the plastic opening tool to pry the clips off Insert the plastic opening tool along the seams at different points to it pry up This may require a bit of force. The USB port cover may fall off in this step.
  • Use the plastic opening tool to pry the clips off

  • Insert the plastic opening tool along the seams at different points to it pry up

  • This may require a bit of force. The USB port cover may fall off in this step.

Aggiungi Commento

Remove the one 3.3mm #00 screw. Remove the one 3.3mm #00 screw.
  • Remove the one 3.3mm #00 screw.

Aggiungi Commento

Use your finger or the plastic opening tool to unclip the board. Be aware of the ribbon cable connected to the motherboard inside the phone.
  • Use your finger or the plastic opening tool to unclip the board.

  • Be aware of the ribbon cable connected to the motherboard inside the phone.

Aggiungi Commento

Peel off the yellow piece of tape from the phone Peel off the yellow piece of tape from the phone
  • Peel off the yellow piece of tape from the phone

Aggiungi Commento

First flip up the retaining flap with your fingernail or a plastic opening tool. Pull on the ribbon cable gently with your fingers Pull on the ribbon cable gently with your fingers
  • First flip up the retaining flap with your fingernail or a plastic opening tool.

  • Pull on the ribbon cable gently with your fingers

Aggiungi Commento

Split apart the motherboard and front panel. Remove the other yellow piece of tape off of the end of the ribbon cable. Split apart the motherboard and front panel. Remove the other yellow piece of tape off of the end of the ribbon cable.
  • Split apart the motherboard and front panel. Remove the other yellow piece of tape off of the end of the ribbon cable.

Aggiungi Commento

Gently pull on the ribbon cable to separate the motherboard. Gently pull on the ribbon cable to separate the motherboard.
  • Gently pull on the ribbon cable to separate the motherboard.

Aggiungi Commento

Pry the LCD screen out using the plastic opening tool and remove it using your fingers. Pry the LCD screen out using the plastic opening tool and remove it using your fingers. Pry the LCD screen out using the plastic opening tool and remove it using your fingers.
  • Pry the LCD screen out using the plastic opening tool and remove it using your fingers.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Nick

Membro da: 28/10/2011

6 Reputazione

3 Guide realizzate

Team

Cal Poly, Team 20-29, Maness Fall 2011 Membro di Cal Poly, Team 20-29, Maness Fall 2011

CPSU-MANESS-F11S20G29

4 Membri

9 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 997