Introduzione

This device's motherboard is a green, "L"-shaped component internally located against the front screen and beneath the battery. Replacement requires the removal of the battery prior to removing the motherboard and involves the disconnection of two gold ribbons and 6 screws. In this guide, you will be removing the following:

  1. Back Cover
  2. Battery
  3. Charging Port
  4. Speaker Unit
  5. Motherboard

If the guide steps are accurately followed, replacement should be a breeze. So, prepare your required tools, a new motherboard for your tablet, and set aside about 20 to 30 minutes to delve into the inner workings of your HP Slate.

Begin your replacement by using a T3 or T4 Torx screwdriver. Remove the two 1.4mm x 3mm Torx Head screws at the top of the device.
  • Begin your replacement by using a T3 or T4 Torx screwdriver.

    • Remove the two 1.4mm x 3mm Torx Head screws at the top of the device.

On the HP 10 Plus 2201 there are no head screws. I used the spudger to 'carefully' separate the case. There are little snaps on the inside of case that will separate with little pressure on spudger.

RB Richter - Replica

I used these directions to replace HP Plus 10 2201 battery. I bypassed speaker installation.

RB Richter - Replica

With the pointed end of the spudger, remove the thin metal band. It is easiest to remove the metal band through the headphone opening.
  • With the pointed end of the spudger, remove the thin metal band.

    • It is easiest to remove the metal band through the headphone opening.

On HP 10 Plus 2201 there is no metal band. The case simply unsnaps apart.

RB Richter - Replica

Using the flat end of the spudger, pry back the rear plastic cover. As you work your way around the edge, several "pop" noises will be made. These noises are caused by the plastic clips coming undone.
  • Using the flat end of the spudger, pry back the rear plastic cover.

    • As you work your way around the edge, several "pop" noises will be made. These noises are caused by the plastic clips coming undone.

This is basically how I opened my HP 10 Plus 2201. "Using the flat end of the spudger, pry back (apart) the rear plastic cover from tablet.

RB Richter - Replica

Remove the rear cover.
  • Remove the rear cover.

Aggiungi Commento

Locate and remove the yellow tape covering the red and white speaker wires.
  • Locate and remove the yellow tape covering the red and white speaker wires.

The inside of my HP 10 Plus 2210 looks similar but not exactly as this illustration

RB Richter - Replica

The battery connections weren't the plug in type. The three battery battery wires (red, white, & black) were soldered into place,

RB Richter - Replica

Using the pointed end of the spudger, push both sides of the speaker wire connector out of its base. Push the same amount on both sides of the connector to avoid jamming or twisting its metal pins.
  • Using the pointed end of the spudger, push both sides of the speaker wire connector out of its base.

    • Push the same amount on both sides of the connector to avoid jamming or twisting its metal pins.

    • Do not yank or pull on the speaker wires, since they are fragile. Only push on the white connector.

Do not pull on wires. Never force anything.

RB Richter - Replica

note the route of the speaker cables round the battery

Alan Boddey - Replica

Gently pull back the foil covering the gold charging port ribbon.
  • Gently pull back the foil covering the gold charging port ribbon.

Aggiungi Commento

Using the flat end of the spudger, lift up the black panel covering the charging port connector. Gently slide the charging port ribbon out from its housing.
  • Using the flat end of the spudger, lift up the black panel covering the charging port connector.

  • Gently slide the charging port ribbon out from its housing.

    • It may be easier to use the pointed end of the spudger than your fingers.

Aggiungi Commento

Lift gold charging strip away from the battery.
  • Lift gold charging strip away from the battery.

Aggiungi Commento

Push the white battery connector out of its housing using the pointed end of the spudger. Push the white battery connector out of its housing using the pointed end of the spudger.
  • Push the white battery connector out of its housing using the pointed end of the spudger.

Aggiungi Commento

Using the #00 Phillips Head screwdriver, remove the 5 screws holding the battery in place.
  • Using the #00 Phillips Head screwdriver, remove the 5 screws holding the battery in place.

    • The four 1.75mm x 3mm silver Phillips Head screws circled in red are interchangeable.

    • The black 1.75mm x 4mm Phillips Head screw must go back to the same spot during reassembly.

Aggiungi Commento

Lift battery out of its place and set aside.
  • Lift battery out of its place and set aside.

Aggiungi Commento

Disconnect the LCD screen ribbon by lifting up the black panel with the flat end of a spudger and sliding the gold strip out. When reconnecting the LCD connector ribbon, make sure that it's pushed in all the way. If it isn't, there will be horizontal lines when you power the tablet on.
  • Disconnect the LCD screen ribbon by lifting up the black panel with the flat end of a spudger and sliding the gold strip out.

    • When reconnecting the LCD connector ribbon, make sure that it's pushed in all the way. If it isn't, there will be horizontal lines when you power the tablet on.

Aggiungi Commento

Likewise, disconnect the square radio chip ribbon by lifting up the black panel with a spudger and sliding the gold strip out. Likewise, disconnect the square radio chip ribbon by lifting up the black panel with a spudger and sliding the gold strip out.
  • Likewise, disconnect the square radio chip ribbon by lifting up the black panel with a spudger and sliding the gold strip out.

Aggiungi Commento

You will be using a #00 Phillips Head screwdriver to free the motherboard. Remove the six 1.75mm x 3mm Phillips Head screws holding the motherboard to the screen.
  • You will be using a #00 Phillips Head screwdriver to free the motherboard.

    • Remove the six 1.75mm x 3mm Phillips Head screws holding the motherboard to the screen.

Aggiungi Commento

Using your hand, lift up the silver tape from the copper plate. Lift the motherboard out of the device.
  • Using your hand, lift up the silver tape from the copper plate.

  • Lift the motherboard out of the device.

    • You may need to wiggle and work the motherboard to get it released from the device

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 4 persone hanno completato questa guida.

Davis Muxlow

Membro da: 14/04/2014

242 Reputazione

1 Guida realizzata

Team

Cal Poly, Team 13-30, Maness Spring 2014 Membro di Cal Poly, Team 13-30, Maness Spring 2014

CPSU-MANESS-S14S13G30

3 Membri

4 Guide realizzate

We have 7 inch Hp tablet please replace motherboard sir

Sushmitha - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 2

Ultimi 7 Giorni: 7

Ultimi 30 Giorni: 24

Tutti i Tempi: 2,912