Introduzione

If the touch pad becomes damaged it will need to be replaced in order for it to properly work. There are a good amount of steps in this process but, it is not too difficult.

Flip the laptop upside down and remove battery by pressing inward on the two latches holding the battery in. Flip the laptop upside down and remove battery by pressing inward on the two latches holding the battery in.
  • Flip the laptop upside down and remove battery by pressing inward on the two latches holding the battery in.

Aggiungi Commento

Unscrew the four (2.5 mm Phillips) screws (Use Phillips #0 Screwdriver). Unscrew the four (2.5 mm Phillips) screws (Use Phillips #0 Screwdriver).
  • Unscrew the four (2.5 mm Phillips) screws (Use Phillips #0 Screwdriver).

Aggiungi Commento

Flip laptop over and open it.
  • Flip laptop over and open it.

Aggiungi Commento

Slightly push up while lifting up on the power button panel to release the panel.
  • Slightly push up while lifting up on the power button panel to release the panel.

Aggiungi Commento

Unscrew the four (2.5 mm Phillips) screws holding the keyboard in (Use Phillips #0 Screwdriver).
  • Unscrew the four (2.5 mm Phillips) screws holding the keyboard in (Use Phillips #0 Screwdriver).

Aggiungi Commento

Carefully (holding both sides of the keyboard), push up and lift slightly. Keyboard is still connected via a ribbon cable.
  • Carefully (holding both sides of the keyboard), push up and lift slightly.

  • Keyboard is still connected via a ribbon cable.

  • Move the keyboard slightly to the left to have access to the keyboard ribbon cable.

Aggiungi Commento

Use the black spudger to lift the black latch holding the keyboard ribbon cable.
  • Use the black spudger to lift the black latch holding the keyboard ribbon cable.

Aggiungi Commento

Unscrew the three (2.5 mm Phillips) screws holding the bottom touchpad panel.
  • Unscrew the three (2.5 mm Phillips) screws holding the bottom touchpad panel.

Aggiungi Commento

Carefully slide the bottom panel to the right.
  • Carefully slide the bottom panel to the right.

  • Keyboard is connected via a wire to the back of the panel.

Aggiungi Commento

Flip the bottom touchpad panel directly towards the screen, being sure to not lift it too high.
  • Flip the bottom touchpad panel directly towards the screen, being sure to not lift it too high.

  • Keep an eye on the ZIF connector underneath, make sure it is not pulled accidentally.

Aggiungi Commento

Using the black spudger, slightly pry up on the ZIF connector and lift out the wire carefully.
  • Using the black spudger, slightly pry up on the ZIF connector and lift out the wire carefully.

Aggiungi Commento

Unscrew the two (2.5 mm Phillips) screws on the touch pad retention panel (Use Phillips #0 screw driver).
  • Unscrew the two (2.5 mm Phillips) screws on the touch pad retention panel (Use Phillips #0 screw driver).

Aggiungi Commento

Slightly push the touch pad retention panel forward to remove from clasp and lift up.
  • Slightly push the touch pad retention panel forward to remove from clasp and lift up.

Aggiungi Commento

Unscrew the following two (2.0 mm Phillips) screws attached to the touchpad (Use Phillips #0 screw driver).
  • Unscrew the following two (2.0 mm Phillips) screws attached to the touchpad (Use Phillips #0 screw driver).

Aggiungi Commento

Slightly lift up the bottom of the touchpad and pull towards you to free the touchpad from the casing
  • Slightly lift up the bottom of the touchpad and pull towards you to free the touchpad from the casing

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Joshua

Membro da: 23/09/2014

88 Reputazione

6 Guide realizzate

Team

USF Tampa, Team 9-5, Blackwell Fall 2014 Membro di USF Tampa, Team 9-5, Blackwell Fall 2014

USFT-BLACKWELL-F14S9G5

4 Membri

10 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 3

Ultimi 30 Giorni: 25

Tutti i Tempi: 610