Introduzione

If there are communication problems between the computer and printer, replacing the motherboard is an option to consider in order to fix this problem. The motherboard controls all operations and functions of the printer enabling it to run properly and communicate with the computer.

Parti

Nessuna parte richiesta.

Open the front access panel by placing your finger in the front slot and pulling gently.
  • Open the front access panel by placing your finger in the front slot and pulling gently.

Aggiungi Commento

Open the protective lid that is covering the glass. Press gently against the base of the panel to remove the lid from the rest of the printer.
  • Open the protective lid that is covering the glass. Press gently against the base of the panel to remove the lid from the rest of the printer.

Aggiungi Commento

Remove the four 9mm T10 Torx screws on the top. Remove the four 9mm T10 Torx screws on the top. Remove the four 9mm T10 Torx screws on the top.
  • Remove the four 9mm T10 Torx screws on the top.

Aggiungi Commento

Carefully lift the top panel off of the printer. Do not tear or damage the two cables that connect the top lid to the motherboard.
  • Carefully lift the top panel off of the printer.

  • Do not tear or damage the two cables that connect the top lid to the motherboard.

Aggiungi Commento

Remove the two cables by gripping each one close to their connection ports on the motherboard and gently disconnecting them. Remove the two cables by gripping each one close to their connection ports on the motherboard and gently disconnecting them. Remove the two cables by gripping each one close to their connection ports on the motherboard and gently disconnecting them.
  • Remove the two cables by gripping each one close to their connection ports on the motherboard and gently disconnecting them.

Aggiungi Commento

The mother board is located at the back of the printer. The mother board is located at the back of the printer.
  • The mother board is located at the back of the printer.

Aggiungi Commento

Take note of the wire's location and orientation as this will be important to properly reassemble your device. Remove all of the wires connected to the mother board. There are seven in total. Remove all of the wires connected to the mother board. There are seven in total.
  • Take note of the wire's location and orientation as this will be important to properly reassemble your device.

  • Remove all of the wires connected to the mother board. There are seven in total.

Aggiungi Commento

Remove the three 9mm T10 Torx screws that hold the motherboard to the body of the printer Remove the three 9mm T10 Torx screws that hold the motherboard to the body of the printer
  • Remove the three 9mm T10 Torx screws that hold the motherboard to the body of the printer

Aggiungi Commento

At this point, the mother board should be free of all connections from the rest of the printer.
  • At this point, the mother board should be free of all connections from the rest of the printer.

  • Remove and replace the mother board with the new one.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 6 persone hanno completato questa guida.

Allen Bailey

Membro da: 15/01/2013

176 Reputazione

1 Guida realizzata

Team

Cal Poly, Team 18-35, Regan Winter 2013 Membro di Cal Poly, Team 18-35, Regan Winter 2013

CPSU-REGAN-W13S18G35

5 Membri

8 Guide realizzate

ok so ineed to replace the Motherboard -- where do I get this board and what is the cost?

Ken Craven - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 9

Ultimi 30 Giorni: 35

Tutti i Tempi: 2,274