Introduzione

Proper maintenance of the Giant Reign 2 bicycle includes installation and lubrication of a new headset. This guide will clearly show you how to perform this maintenance quickly and safely, extending the life of your bike.

Using the 4mm Allen wrench, partially unscrew the 4 (22mm) hex screws on the front of the axle casing to allow the axle to slide freely.
  • Using the 4mm Allen wrench, partially unscrew the 4 (22mm) hex screws on the front of the axle casing to allow the axle to slide freely.

Aggiungi Commento

Using the 8mm Allen wrench, loosen the axle screw until 1/2 of the axle screw is visible. Push the axle screw to reveal the axle rod on the other side.
  • Using the 8mm Allen wrench, loosen the axle screw until 1/2 of the axle screw is visible.

  • Push the axle screw to reveal the axle rod on the other side.

Aggiungi Commento

Using the Allen wrench, finish unscrewing the axle screw and pull it out.
  • Using the Allen wrench, finish unscrewing the axle screw and pull it out.

  • Hold the wheel when pulling out the axle rod so that the bike does not fall.

Aggiungi Commento

Pull the wheel from the fork.
  • Pull the wheel from the fork.

Aggiungi Commento

Using the 8mm Allen wrench, unscrew 2  (32mm) screws to release the brake calipers from the fork. If necessary use wire cutters to release zip ties attaching cables to the forks.
  • Using the 8mm Allen wrench, unscrew 2 (32mm) screws to release the brake calipers from the fork.

  • If necessary use wire cutters to release zip ties attaching cables to the forks.

Aggiungi Commento

Using the 8mm Allen wrench, unscrew the 30mm head screw located on top of the steam. Using the 4mm Allen wrench, loosen the side screw on both sides. Lift off the handlebar.
  • Using the 8mm Allen wrench, unscrew the 30mm head screw located on top of the steam.

  • Using the 4mm Allen wrench, loosen the side screw on both sides.

  • Lift off the handlebar.

  • Hang the handlebar gently from the cables. Do not pull the cables as you may damage the brake/derailleur lines.

Aggiungi Commento

Slide off the spacers. Lift off the seal. Lift off the seal.
  • Slide off the spacers.

  • Lift off the seal.

Aggiungi Commento

Slide the fork out of the casing.
  • Slide the fork out of the casing.

Aggiungi Commento

Using your fingers, pry the bearings from the top and bottom of the headset.
  • Using your fingers, pry the bearings from the top and bottom of the headset.

Aggiungi Commento

Apply WD-40 to both ends of the headset and bearings.
  • Apply WD-40 to both ends of the headset and bearings.

  • Dry headset and bearings with paper towels.

  • Repeat as necessary until clean.

Aggiungi Commento

Using your finger, apply all-purpose lube to the bearings and each end of the headset. Insert the bearings into the headset with the beveled side facing into the headset.
  • Using your finger, apply all-purpose lube to the bearings and each end of the headset.

  • Insert the bearings into the headset with the beveled side facing into the headset.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Sterling Grande

Membro da: 08/10/2012

126 Reputazione

4 Guide realizzate

Team

Cal Poly, Team 9-14, Amido Fall 2012 Membro di Cal Poly, Team 9-14, Amido Fall 2012

CPSU-AMIDO-F12S9G14

4 Membri

6 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 5

Ultimi 30 Giorni: 39

Tutti i Tempi: 2,879