Salta al contenuto principale

Garmin GPS V Logic Board Replacement

Cosa ti serve

  1. Garmin GPS V Logic Board Replacement, Logic Board: passo 1, immagine 1 di 3 Garmin GPS V Logic Board Replacement, Logic Board: passo 1, immagine 2 di 3 Garmin GPS V Logic Board Replacement, Logic Board: passo 1, immagine 3 di 3
    • Orient the GPS V backside up.

    • With a #0 Philips screwdriver, remove six M2x0.4 black screws on the back of the unit.

  2. Garmin GPS V Logic Board Replacement: passo 2, immagine 1 di 2 Garmin GPS V Logic Board Replacement: passo 2, immagine 2 di 2
    • With the spudger, gently pry the back plate off the unit starting at the corners.

    • Open the back plate about 35°, use the antenna side act like a hinge.

    • Do NOT remove the back plate all the way, there are cables connected to it.

  3. Garmin GPS V Logic Board Replacement: passo 3, immagine 1 di 2 Garmin GPS V Logic Board Replacement: passo 3, immagine 2 di 2
    • Locate the white 8-pin connector on the logic board and disconnect it.

    • Open the device all the way, making sure to not disconnect the brown antenna wire.

  4. Garmin GPS V Logic Board Replacement: passo 4, immagine 1 di 2 Garmin GPS V Logic Board Replacement: passo 4, immagine 2 di 2
    • With a #1 Philips screwdriver, remove the silver M2x0.4 screw on the logic board near the brown wire.

    • You may need to rotate the device to get better access to the screw.

  5. Garmin GPS V Logic Board Replacement: passo 5, immagine 1 di 3 Garmin GPS V Logic Board Replacement: passo 5, immagine 2 di 3 Garmin GPS V Logic Board Replacement: passo 5, immagine 3 di 3
    • Locate the ribbon connector on the logic board.

    • With the spudger, gently apply pressure to both sides of the brown connector lock until it pushes out.

    • With the spudger, gently work the ribbon cable out of the connector until it is free.

  6. Garmin GPS V Logic Board Replacement: passo 6, immagine 1 di 2 Garmin GPS V Logic Board Replacement: passo 6, immagine 2 di 2
    • With the spudger, gently pry out the logic board.

    • Be careful to not disconnect the brown antenna wire as you remove the logic board.

  7. Garmin GPS V Logic Board Replacement: passo 7, immagine 1 di 1
    • Locate the brown wire connection on the logic board.

    • Carefully apply heat with the soldering iron while gently pulling on the brown wire.

    • It may take some time to heat the flux up before the wire can be pulled out.

    • Pull brown wire free of the logic board.

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Connor

Membro da: 01/23/12

194 Reputazione

4 Guide realizzate

Team

Cal Poly, Team 3-25, Amido Winter 2012 Membro di Cal Poly, Team 3-25, Amido Winter 2012

CPSU-AMIDO-W12S3G25

4 Membri

4 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 4

Tutti i Tempi: 5,573