Introduzione

This guide will illustrate how to install a new headphone jack on an original Game Boy system. You'll need to know how to solder for this replacement, so be sure to check out iFixit's soldering technique guide.

Switch your Game Boy off and remove the cartridge. Switch your Game Boy off and remove the cartridge.
  • Switch your Game Boy off and remove the cartridge.

Aggiungi Commento

Use a fingernail (or small coin) to push down on the battery door latch and remove the battery door. The release latch is a plastic spring clip. If your Game Boy is getting on in years, be careful as the plastic may be brittle. When you're replacing the cover, be sure to get its two plastic tabs into the slots in the bottom of the battery compartment before pushing the cover back in place.
  • Use a fingernail (or small coin) to push down on the battery door latch and remove the battery door.

    • The release latch is a plastic spring clip. If your Game Boy is getting on in years, be careful as the plastic may be brittle.

    • When you're replacing the cover, be sure to get its two plastic tabs into the slots in the bottom of the battery compartment before pushing the cover back in place.

Aggiungi Commento

Use a fingernail to pry each battery outward from the positive (+) terminal to remove them. Dispose of used batteries properly!
  • Use a fingernail to pry each battery outward from the positive (+) terminal to remove them.

    • Dispose of used batteries properly!

    • Remove the batteries from your Game Boy before storing it for more than a month or so.

Aggiungi Commento

Remove the six Triwing screws from the back of the device.
  • Remove the six Triwing screws from the back of the device.

Aggiungi Commento

Gently separate the device's front casing from the back casing after you remove the screws.
  • Gently separate the device's front casing from the back casing after you remove the screws.

    • Be careful not to completely separate the casing halves, as they are still joined by a large ribbon cable that may be damaged.

Aggiungi Commento

Slide the front side of the casing down to expose the ribbon cable connector.
  • Slide the front side of the casing down to expose the ribbon cable connector.

Aggiungi Commento

Grip the ribbon connector with your thumb and forefinger. Pull down gently until the connector, not the ribbon itself, comes out of its socket.
  • Grip the ribbon connector with your thumb and forefinger. Pull down gently until the connector, not the ribbon itself, comes out of its socket.

  • Separate the front and back casings.

Aggiungi Commento

The headphone jack is located on the bottom of the rear outer casing,  near the battery compartment. Use a Phillips #00 screwdriver to remove the two screws holding the headphone jack in place.
  • The headphone jack is located on the bottom of the rear outer casing, near the battery compartment.

  • Use a Phillips #00 screwdriver to remove the two screws holding the headphone jack in place.

Aggiungi Commento

Once the headphone jack is detached it will dangle by the wires attached to the main circuit board. Do not worry about the connections, they are solid and will not break. Use a Phillips#00 screwdriver to remove the two screws that hold the main circuit board to the casing. This will allow access to the connection points of the headphone jack.
  • Once the headphone jack is detached it will dangle by the wires attached to the main circuit board. Do not worry about the connections, they are solid and will not break.

  • Use a Phillips#00 screwdriver to remove the two screws that hold the main circuit board to the casing. This will allow access to the connection points of the headphone jack.

Aggiungi Commento

Use a plastic opening tool to remove the main circuit board from the casing. Once the main circuit board is removed, set aside the outer casing.
  • Use a plastic opening tool to remove the main circuit board from the casing.

  • Once the main circuit board is removed, set aside the outer casing.

Aggiungi Commento

Desolder the four wires connecting the headphone jack to the motherboard. Desolder the four wires connected to the headphone jack To learn more about soldering, check out iFixit's soldering technique guide.
  • Desolder the four wires connecting the headphone jack to the motherboard.

  • Desolder the four wires connected to the headphone jack

  • To learn more about soldering, check out iFixit's soldering technique guide.

  • Remove the headphone jack with tweezers.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 10 persone hanno completato questa guida.

Andrew Tramposch

Membro da: 24/06/2010

1.487 Reputazione

11 Guide realizzate

Team

Cal Poly, Team 3-2, Johann Summer 2010 Membro di Cal Poly, Team 3-2, Johann Summer 2010

CPSU-JOHANN-R10S3G2

3 Membri

11 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 3

Ultimi 7 Giorni: 21

Ultimi 30 Giorni: 111

Tutti i Tempi: 12,295