Parti

Nessuna parte richiesta.

A Phillips Head Size Zero Screw Driver
  • A Phillips Head Size Zero Screw Driver

Aggiungi Commento

Using a Phillips-head screwdriver, remove each of the 3 screws from the underside of the camera head.
  • Using a Phillips-head screwdriver, remove each of the 3 screws from the underside of the camera head.

Aggiungi Commento

Gently pull back the base and set it aside.
  • Gently pull back the base and set it aside.

  • Be careful not to pull out the USB cable attachment when taking off the base

Aggiungi Commento

Gently remove the white connector with the red, green, white & black cord with your fingers. This connector is the end of the USB cable. Gently remove the white connector with the red, green, white & black cord with your fingers. This connector is the end of the USB cable. Gently remove the white connector with the red, green, white & black cord with your fingers. This connector is the end of the USB cable.
  • Gently remove the white connector with the red, green, white & black cord with your fingers. This connector is the end of the USB cable.

Aggiungi Commento

Press tab on inside of device to release silver ring. Gently remove top (silver) ring of lens casing with your fingers. Gently remove top (silver) ring of lens casing with your fingers.
  • Press tab on inside of device to release silver ring.

  • Gently remove top (silver) ring of lens casing with your fingers.

Aggiungi Commento

Gently remove inner casing of the lens (silver with a black ring). Be careful not to break the small notch at the top, which holds the inner casing in place.
  • Gently remove inner casing of the lens (silver with a black ring).

  • Be careful not to break the small notch at the top, which holds the inner casing in place.

Aggiungi Commento

Remove the small, black, ridged inner ring around the lens with your fingers. Remove the small, black, ridged inner ring around the lens with your fingers.
  • Remove the small, black, ridged inner ring around the lens with your fingers.

Aggiungi Commento

Unscrew the lens counterclockwise with your fingers. Unscrew the lens counterclockwise with your fingers.
  • Unscrew the lens counterclockwise with your fingers.

Aggiungi Commento

Turn the hollow outer casing so that you can see inside of it. Gently pull out main board with fingers.
  • Turn the hollow outer casing so that you can see inside of it.

  • Gently pull out main board with fingers.

Aggiungi Commento

Insert your new board into the outer casing. Be sure that it rests firmly between the sets of rails on either side. Insert your new board into the outer casing. Be sure that it rests firmly between the sets of rails on either side.
  • Insert your new board into the outer casing. Be sure that it rests firmly between the sets of rails on either side.

Aggiungi Commento

Twist the lens piece in clockwise and then insert black ring around the lens. Twist the lens piece in clockwise and then insert black ring around the lens.
  • Twist the lens piece in clockwise and then insert black ring around the lens.

Aggiungi Commento

Line up notch on inner lens casing (silver with black ring) with notch on body of camera. Gently push it into place, being sure not to break the notch. Insert the silver ring. You should hear it click into place. Insert the silver ring. You should hear it click into place.
  • Line up notch on inner lens casing (silver with black ring) with notch on body of camera. Gently push it into place, being sure not to break the notch.

  • Insert the silver ring. You should hear it click into place.

Aggiungi Commento

Hold the camera in one hand with the hollow side facing up. Hold the USB cable in your other hand with the four small holes facing up. Plug the USB cable into the port.
  • Hold the camera in one hand with the hollow side facing up.

  • Hold the USB cable in your other hand with the four small holes facing up.

  • Plug the USB cable into the port.

Aggiungi Commento

Lay the USB cord in the notch at the base of the camera bottom.
  • Lay the USB cord in the notch at the base of the camera bottom.

  • Place the bottom back onto the camera top.

Aggiungi Commento

Line up the base of the camera with the screw holes.
  • Line up the base of the camera with the screw holes.

  • Use a Phillips-head screwdriver to twist the three screws back into place.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Lyndsi

Membro da: 13/10/2014

7 Reputazione

1 Guida realizzata

Team

Ohio State, Team 1-5, Mccook Fall 2014 Membro di Ohio State, Team 1-5, Mccook Fall 2014

OSU-MCCOOK-F14S1G5

4 Membri

1 Guida realizzata

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 3

Tutti i Tempi: 299