Introduzione

To get to the inside parts of the printer, the housing components must come off.

Turn off the printer.
  • Turn off the printer.

  • Disconnect all data connections coming into the printer such as USB, networkd cables, firewire, etc. as well as removing the power cord.

Aggiungi Commento

Locate the IEEE cover in  the back. Gently slide cover to the right to unlatch then pull to remove it.
  • Locate the IEEE cover in the back.

  • Gently slide cover to the right to unlatch then pull to remove it.

Aggiungi Commento

Using a #2 Phillips screwdriver, remove the four 10mm screws shown. Remove the 6mm screw that holds the rear housing in place.
  • Using a #2 Phillips screwdriver, remove the four 10mm screws shown.

  • Remove the 6mm screw that holds the rear housing in place.

Aggiungi Commento

Remove the rear housing by pulling it backwards. Remove the rear housing by pulling it backwards.
  • Remove the rear housing by pulling it backwards.

Aggiungi Commento

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Insert the flathead screwdriver or plastic pry tool into the cutouts of the lower housing. Release the two tabs of the side housing by lifting the tool in an upward motion Remove the side housing by pulling it outwards.
  • Insert the flathead screwdriver or plastic pry tool into the cutouts of the lower housing.

  • Release the two tabs of the side housing by lifting the tool in an upward motion

  • Remove the side housing by pulling it outwards.

Aggiungi Commento

Both side housings are attached by the same type of mechanism. Using the same method, remove the other side housing.
  • Both side housings are attached by the same type of mechanism.

  • Using the same method, remove the other side housing.

Aggiungi Commento

Lift the paper support. Open the printer cover and front cover. Open the printer cover and front cover.
  • Lift the paper support.

  • Open the printer cover and front cover.

Aggiungi Commento

Remove the four 10 mm Phillips #2 screws from the sides of the printer. Remove the three 6mm Phillips #2 screws. Remove the three 6mm Phillips #2 screws.
  • Remove the four 10 mm Phillips #2 screws from the sides of the printer.

  • Remove the three 6mm Phillips #2 screws.

Aggiungi Commento

Detach the tabs from the pins on each side by pulling it outwards. Detach the tabs from the pins on each side by pulling it outwards.
  • Detach the tabs from the pins on each side by pulling it outwards.

Aggiungi Commento

Remove the two 10 mm Phillips #2 screws on the front of the printer. Remove the two 10 mm Phillips #2 screws on the front of the printer.
  • Remove the two 10 mm Phillips #2 screws on the front of the printer.

Aggiungi Commento

Disconnect the cable on the side by carefully pulling it outwards. You may need to gently rock the cable up and down while pulling. You may need to gently rock the cable up and down while pulling.
  • Disconnect the cable on the side by carefully pulling it outwards.

  • You may need to gently rock the cable up and down while pulling.

Aggiungi Commento

Remove the upper housing by lifting it upwards. It's easier to lift  the housing by gripping it from the bottom.
  • Remove the upper housing by lifting it upwards.

  • It's easier to lift the housing by gripping it from the bottom.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 5 persone hanno completato questa guida.

Larry Huang

Membro da: 12/10/2011

686 Reputazione

4 Guide realizzate

Team

Cal Poly, Team 17-11, Regan Fall 2011 Membro di Cal Poly, Team 17-11, Regan Fall 2011

CPSU-REGAN-F11S17G11

4 Membri

6 Guide realizzate

Thank you so much, Larry! I am repurposing my 1400 for sublimation printing and need to get the print head a little easier than standard methods! Much appreciated!

ryan Caputo - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 21

Tutti i Tempi: 5,313