Aggiusta la tua roba Comunità Store

Epson PPC650 Screen Replacement

Cosa ti serve

  1. Epson PPC650 Screen Replacement, Case: passo 1, immagine 1 di 3 Epson PPC650 Screen Replacement, Case: passo 1, immagine 2 di 3 Epson PPC650 Screen Replacement, Case: passo 1, immagine 3 di 3

    • Make sure the camera is turned off here.

    • Remove batteries from the battery compartment located on the bottom of the camera

    • Remove SD card for the card reader compartment located on the flat side (left side) of the camera

    Traduci

  2. Epson PPC650 Screen Replacement: passo 2, immagine 1 di 1

    • Remove 2 screws on the rounded side of the camera wisdom here.

    Traduci

  3. Epson PPC650 Screen Replacement: passo 3, immagine 1 di 2 Epson PPC650 Screen Replacement: passo 3, immagine 2 di 2

    • Remove 3 screws on the flat side of the camera

    • All silver screws go into the side of the camera that is silver

    • All black screws go into the side of the camera that is black

    Traduci

  5. Epson PPC650 Screen Replacement: passo 4, immagine 1 di 1

    • Remove 4 screws from the bottom of the camera

    • All silver screws go into the side of the camera that is silver

    • All black screws go into the side of the camera that is black

    Traduci

  6. Epson PPC650 Screen Replacement: passo 5, immagine 1 di 3 Epson PPC650 Screen Replacement: passo 5, immagine 2 di 3 Epson PPC650 Screen Replacement: passo 5, immagine 3 di 3

    • Separate the front and back pieces of the cameras plastic casing using a spudgerm here.

    • WARNING: When pulling the front plastic casing, be careful of the wire that are connected to the aperture control

    • Use minimal force so that the plastic casing does not break

    • When separating the small silver sliding indicator for view/off/playback may fall out

    • The plastic viewing window located on the top of the camera may also become lose and fall out

    Traduci

  7. Epson PPC650 Screen Replacement, Screen: passo 6, immagine 1 di 3 Epson PPC650 Screen Replacement, Screen: passo 6, immagine 2 di 3 Epson PPC650 Screen Replacement, Screen: passo 6, immagine 3 di 3

    • Remove copper sheet from the front paneling and back.

    • You will need to use a spudger to unsolder the copper paneling

    • Use the spudger to separate the back circuit board from the camera

    Traduci

  8. Epson PPC650 Screen Replacement: passo 7, immagine 1 di 2 Epson PPC650 Screen Replacement: passo 7, immagine 2 di 2

    • The picture viewing screen is glued to the backing as well as wired in with pink and white wires.

    • Exert minimal force required to pull the screen loose from the camera

    • Remove the pink and white wiring from the internal paneling. These wires are soldered in

    • Remove the orange data hookup cable which feeds into the back circuit board

    Traduci

    • Once all wires have been detached and the old screen has been removed place the new screen into the camera.

    • Insert data hookup into the back of the camera and into the new screen

    • Re-solder the new pink and white wire onto the internal circuit board

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 5 altri collaboratori

Anne

Membro da: 02/12/13

101 Reputazione

1 Guida realizzata

Distintivi: 3

Team

Ohio State, Team 1-5, Buehl Spring 2013 Membro di Ohio State, Team 1-5, Buehl Spring 2013

OSU-BUEHL-S13S1G5

4 Membri

6 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 2

Tutti i Tempi: 366