Aggiusta la tua roba Comunità Store

Disassembling Planet Eclipse Etha Frame

Introduzione

Removing the frame will allow access to the eyes and solenoid should they need replacement.

Cosa ti serve

  1. Disassembling Planet Eclipse Etha Frame, Regulator: passo 1, immagine 1 di 2 Disassembling Planet Eclipse Etha Frame, Regulator: passo 1, immagine 2 di 2

    • Firmly grasp hold of the ring on the bottom of the 90 degree silver fitting on the front of the gun.

    • Pull hard, but slowly, on the macroline where it comes out of silver piece until it comes out.

    • The macroline is the black hose connecting the regulator to the tank connection.

    Traduci

  2. Disassembling Planet Eclipse Etha Frame: passo 2, immagine 1 di 2 Disassembling Planet Eclipse Etha Frame: passo 2, immagine 2 di 2

    • Remove the regulator by unscrewing it in a clockwise direction.

    Traduci

  3. Disassembling Planet Eclipse Etha Frame, Battery and Grip Panels: passo 3, immagine 1 di 2 Disassembling Planet Eclipse Etha Frame, Battery and Grip Panels: passo 3, immagine 2 di 2

    • Use the 5/64" hex key to remove the screw shown.

    • Remove the grip panel by gently holding the bottom of the panel and lifting the panel off.

    • If you are only replacing the battery, skip the next step.

    • The screws in this guide are interchangeable with those shown in the Eyes replacement guide.

    Traduci

  5. Disassembling Planet Eclipse Etha Frame: passo 4, immagine 1 di 1

    • Flip the marker over and use the 5/64" hex key to remove the screw shown.

    • Remove the grip panel by gently holding the bottom of the panel and lifting the panel off.

    Traduci

  6. Disassembling Planet Eclipse Etha Frame: passo 5, immagine 1 di 2 Disassembling Planet Eclipse Etha Frame: passo 5, immagine 2 di 2

    • Carefully remove the 9V battery and connector.

    • Remove the 9V battery from the connector.

    Traduci

  7. Disassembling Planet Eclipse Etha Frame, Frame: passo 6, immagine 1 di 2 Disassembling Planet Eclipse Etha Frame, Frame: passo 6, immagine 2 di 2

    • Carefully disconnect the three connectors from the circuit board.

    • Don't worry about remembering which direction the connectors go in, they will not fit in the board in the wrong direction.

    Traduci

  8. Disassembling Planet Eclipse Etha Frame: passo 7, immagine 1 di 2 Disassembling Planet Eclipse Etha Frame: passo 7, immagine 2 di 2

    • Use the 1/8" hex key to remove the two dome-headed screws by rotating them counter-clockwise.

    Traduci

  9. Disassembling Planet Eclipse Etha Frame: passo 8, immagine 1 di 1

    • Be very careful during the step to avoid damage to the solenoid or wiring.

    • Gently separate the top and bottom of the marker.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 4 altri collaboratori

nicholasj6

Membro da: 10/14/14

261 Reputazione

2 Guide realizzate

Distintivi: 9

+6 altri distintivi

Team

Cal Poly, Team 10-42, Amido Fall 2014 Membro di Cal Poly, Team 10-42, Amido Fall 2014

CPSU-AMIDO-F14S10G42

5 Membri

7 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 1

Tutti i Tempi: 374