Introduzione

In this repair guide you will be able to install a new mother board into the printer.

Parti

Nessuna parte richiesta.

Rotate the photo printer so that the bottom of the case faces upward.
  • Rotate the photo printer so that the bottom of the case faces upward.

Aggiungi Commento

Use a Phillips #2 screwdriver to remove the three 5.65 mm screws on the bottom panel of the case in a counter-clockwise fashion.
  • Use a Phillips #2 screwdriver to remove the three 5.65 mm screws on the bottom panel of the case in a counter-clockwise fashion.

Aggiungi Commento

Rotate the device so that it is upright again. Under the LCD Panel there is a 9.62 mm screw, unscrew using a Phillips #2 screwdriver.
  • Rotate the device so that it is upright again. Under the LCD Panel there is a 9.62 mm screw, unscrew using a Phillips #2 screwdriver.

Aggiungi Commento

Remove the back panel of the case by pulling directly back.
  • Remove the back panel of the case by pulling directly back.

    • Some carefully applied force may be required to remove this part.

Aggiungi Commento

Rotate the photo printer so that the bottom panel faces up once again. Now lift off the bottom panel of the case to access all internal components.
  • Rotate the photo printer so that the bottom panel faces up once again. Now lift off the bottom panel of the case to access all internal components.

Aggiungi Commento

Finally remove the side panel with the ink-cartridge door by holding the right side  and pulling backwards with the left side. Caution! The side panel is held in by tabs; don't break these.
  • Finally remove the side panel with the ink-cartridge door by holding the right side and pulling backwards with the left side.

    • Caution! The side panel is held in by tabs; don't break these.

Aggiungi Commento

Carefully remove the inner components of the device by lifting the inner components up and out of the casing.
  • Carefully remove the inner components of the device by lifting the inner components up and out of the casing.

Aggiungi Commento

Locate the red and black cable that is connecting the fan to the top of the logic board.
  • Locate the red and black cable that is connecting the fan to the top of the logic board.

Aggiungi Commento

Carefully, remove the red and black cable from the logic board by pulling gently in order to isolate the cooling fan from the device.
  • Carefully, remove the red and black cable from the logic board by pulling gently in order to isolate the cooling fan from the device.

Aggiungi Commento

Locate the data ribbon that connects the LCD panel to the mother board. Loosen the fasteners next to the ribbon by carefully pushing them away from the white ribbon holder. Once the fasteners are loosened the ribbon should easily slide away from the motherboard.
  • Locate the data ribbon that connects the LCD panel to the mother board.

  • Loosen the fasteners next to the ribbon by carefully pushing them away from the white ribbon holder.

    • Once the fasteners are loosened the ribbon should easily slide away from the motherboard.

Aggiungi Commento

Locate the clips with multi-colored wires that connect the motherboard to the printing unit. Disconnect both of them by gently pulling them away from the motherboard. Disconnect both of them by gently pulling them away from the motherboard.
  • Locate the clips with multi-colored wires that connect the motherboard to the printing unit.

    • Disconnect both of them by gently pulling them away from the motherboard.

Aggiungi Commento

Locate the white ribbon that connects the motherboard to the printing feed. Disconnect the ribbon by gently pulling the ribbon away from the motherboard. Disconnect the ribbon by gently pulling the ribbon away from the motherboard.
  • Locate the white ribbon that connects the motherboard to the printing feed.

  • Disconnect the ribbon by gently pulling the ribbon away from the motherboard.

Aggiungi Commento

The mother board has changed orientation. Notice the new orientation based on the white data ribbon we removed in the previous step. Locate the black data ribbon that connects the mother board to the printing motors.
  • The mother board has changed orientation. Notice the new orientation based on the white data ribbon we removed in the previous step.

  • Locate the black data ribbon that connects the mother board to the printing motors.

  • Disconnect it from the logic board, by gently pulling the wire away from the mother board.

Aggiungi Commento

Now unscrew the three screws 7.89mm (counter-clockwise) using a Phillips #1 screwdriver.
  • Now unscrew the three screws 7.89mm (counter-clockwise) using a Phillips #1 screwdriver.

Aggiungi Commento

Once screws and ribbons are disconnected, you can pull mother board away from the printing unit.
  • Once screws and ribbons are disconnected, you can pull mother board away from the printing unit.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Cory Peterson

Membro da: 04/04/2012

133 Reputazione

1 Guida realizzata

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 567