Salta al contenuto principale

Coby DVD-R11000 I/O Ports Replacement

Cosa ti serve

  1. Coby DVD-R11000 I/O Ports Replacement, Outer Casing: passo 1, immagine 1 di 3 Coby DVD-R11000 I/O Ports Replacement, Outer Casing: passo 1, immagine 2 di 3 Coby DVD-R11000 I/O Ports Replacement, Outer Casing: passo 1, immagine 3 di 3
    • Remove the four 1cm screws, two on each side, of the DVD player with the Phillips #1 screwdriver.

    • Remove the five 1cm screws on the back of the DVD player with the Phillips #1 screwdriver.

    • It is not required to remove the other seven screws in the middle between the I/O ports.

  2. Coby DVD-R11000 I/O Ports Replacement: passo 2, immagine 1 di 3 Coby DVD-R11000 I/O Ports Replacement: passo 2, immagine 2 di 3 Coby DVD-R11000 I/O Ports Replacement: passo 2, immagine 3 di 3
    • Position the DVD player so that the back is facing you

    • Grab underneath the sides of the DVD player and lift the front of it upwards.

    • Carefully pull the top of the casing off

  3. Coby DVD-R11000 I/O Ports Replacement, 3-Pin Power Cable: passo 3, immagine 1 di 2 Coby DVD-R11000 I/O Ports Replacement, 3-Pin Power Cable: passo 3, immagine 2 di 2
    • Gently pinch the 3-pin white adapter of the wire connecting the power cord to the circuit board.

    • Remove the wire from the circuit board.

  4. Coby DVD-R11000 I/O Ports Replacement, Circuit Boards: passo 4, immagine 1 di 2 Coby DVD-R11000 I/O Ports Replacement, Circuit Boards: passo 4, immagine 2 di 2
    • Position the DVD player so that the side with golden circuit board, where the power cord was plugged into, is closest to you.

    • Remove the black wire with the 6-pin white adapter, which is adjacent to the other three pin adapter wires on the golden circuit board.

  5. Coby DVD-R11000 I/O Ports Replacement: passo 5, immagine 1 di 3 Coby DVD-R11000 I/O Ports Replacement: passo 5, immagine 2 di 3 Coby DVD-R11000 I/O Ports Replacement: passo 5, immagine 3 di 3
    • Position the DVD player so that the back panel is facing you.

    • Remove the three wires with the white pin adapters from the golden circuit board.

  6. Coby DVD-R11000 I/O Ports Replacement: passo 6, immagine 1 di 3 Coby DVD-R11000 I/O Ports Replacement: passo 6, immagine 2 di 3 Coby DVD-R11000 I/O Ports Replacement: passo 6, immagine 3 di 3
    • Remove the four half inch screws, located at each corner of the golden circuit board, using the Phillips #1 screwdriver.

    • Place the blue plastic tool opener underneath the side of the circuit board and carefully remove it from the DVD player.

  7. Coby DVD-R11000 I/O Ports Replacement: passo 7, immagine 1 di 3 Coby DVD-R11000 I/O Ports Replacement: passo 7, immagine 2 di 3 Coby DVD-R11000 I/O Ports Replacement: passo 7, immagine 3 di 3
    • Position the DVD player so that the front is facing you.

    • Using the tweezers and the blue plastic opening tool, disconnect the ribbon cables from the green circuit board where the I/O ports are attach to.

  8. Coby DVD-R11000 I/O Ports Replacement: passo 8, immagine 1 di 3 Coby DVD-R11000 I/O Ports Replacement: passo 8, immagine 2 di 3 Coby DVD-R11000 I/O Ports Replacement: passo 8, immagine 3 di 3
    • Remove the three wires with the white pin adapters from the green circuit board that you just disconnected the ribbon wires from.

  9. Coby DVD-R11000 I/O Ports Replacement: passo 9, immagine 1 di 3 Coby DVD-R11000 I/O Ports Replacement: passo 9, immagine 2 di 3 Coby DVD-R11000 I/O Ports Replacement: passo 9, immagine 3 di 3
    • Remove the seven 1cm screws located on the back panel of the outer casing, in between the I/O ports, with the Phillips #1 screwdriver

    • Grab the sides of the back panel and remove it from the DVD player.

  10. Coby DVD-R11000 I/O Ports Replacement: passo 10, immagine 1 di 2 Coby DVD-R11000 I/O Ports Replacement: passo 10, immagine 2 di 2
    • Remove the two 1cm screws that are circled in red.

    • Place the blue plastic tool opener underneath the side of the circuit board and carefully remove it from the DVD player.

  11. Coby DVD-R11000 I/O Ports Replacement, I/O Ports: passo 11, immagine 1 di 1
    • De-solder the electrical components contained in the red rectangles from the green circuit board, which is the second one you removed.

    • Each red rectangle contains the electrical components for a specific group of I/O ports

Conclusione

To reassemble your device, follow these instructions in reverse order.

Andrew

Membro da: 10/22/14

501 Reputazione

5 Guide realizzate

Team

UMass Dartmouth, Team 1-6, Shastany Fall 2014 Membro di UMass Dartmouth, Team 1-6, Shastany Fall 2014

UMASSD-SHASTANY-F14S1G6

4 Membri

5 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 3

Tutti i Tempi: 173