Introduzione

This manual provides instructions on how to clean the tube and butterfly valve of the throttle body as well as clean and protect the electrical contacts

Firstly Disconnect  battery Always take the negative terminal off first.
  • Firstly Disconnect battery

    • Always take the negative terminal off first.

    • '''General Tip After disconnecting the battery leave the car for about 10 mins , This lets any residual energy left in the electrical system to dissapate. It is good practise whatever the job

Aggiungi Commento

Locate throttle body on right side of engine, it is between the intake tube and intake manifold.
  • Locate throttle body on right side of engine, it is between the intake tube and intake manifold.

Aggiungi Commento

Locate throttle linkage cable assembly.
  • Locate throttle linkage cable assembly.

Aggiungi Commento

Twist the assembly clockwise. Twist the assembly clockwise.
  • Twist the assembly clockwise.

Aggiungi Commento

Slide both slackened cables off assembly’s guides.
  • Slide both slackened cables off assembly’s guides.

Aggiungi Commento

Locate the two hoses on the top of the throttle body. Gently lift the hoses off.
  • Locate the two hoses on the top of the throttle body.

  • Gently lift the hoses off.

Aggiungi Commento

Use a flat head screwdriver to loosen the hose clamp attaching the intake tube to the throttle body.
  • Use a flat head screwdriver to loosen the hose clamp attaching the intake tube to the throttle body.

Aggiungi Commento

Remove the intake tube from the throttle body.
  • Remove the intake tube from the throttle body.

Aggiungi Commento

Locate wiring clip on the underside of the throttle body.
  • Locate wiring clip on the underside of the throttle body.

Aggiungi Commento

Press down on the locking mechanism before gently removing the wiring clip. Press down on the locking mechanism before gently removing the wiring clip.
  • Press down on the locking mechanism before gently removing the wiring clip.

Aggiungi Commento

Locate throttle linkage arm. Open the locking clip with a flat head screwdriver. Pry off the linkage arm with a flat head screwdriver.
  • Locate throttle linkage arm.

  • Open the locking clip with a flat head screwdriver.

  • Pry off the linkage arm with a flat head screwdriver.

Aggiungi Commento

Locate the three 13mm nuts attaching the throttle body to the intake manifold. Remove nuts with a 13mm crescent wrench. Remove nuts with a 13mm crescent wrench.
  • Locate the three 13mm nuts attaching the throttle body to the intake manifold.

  • Remove nuts with a 13mm crescent wrench.

Aggiungi Commento

Lift the throttle body off of the intake manifold.
  • Lift the throttle body off of the intake manifold.

  • The manifold is now out of the engine bay and ready for cleaning or adjustment.

Aggiungi Commento

Cover the electrical contacts with a shop towel to prevent throttle body cleaner from inadvertently spilling over. Cover the electrical contacts with a shop towel to prevent throttle body cleaner from inadvertently spilling over.
  • Cover the electrical contacts with a shop towel to prevent throttle body cleaner from inadvertently spilling over.

Aggiungi Commento

Liberally apply throttle body cleaner to the inside of throttle body and butterfly valve.
  • Liberally apply throttle body cleaner to the inside of throttle body and butterfly valve.

  • Use a shop towel sprayed with cleaner to wipe off thick grime if severely dirtied.

Aggiungi Commento

Spray electrical cleaner on the metal contacts to blast away particles in the bracket. Spray off the wiring clip that attaches to the throttle body inside the engine bay.
  • Spray electrical cleaner on the metal contacts to blast away particles in the bracket.

  • Spray off the wiring clip that attaches to the throttle body inside the engine bay.

Aggiungi Commento

Apply a small amount of dielectric grease to the metal contacts to prevent corrosion.
  • Apply a small amount of dielectric grease to the metal contacts to prevent corrosion.

Aggiungi Commento

Conclusione

To reinstall the throttle body after cleaning follow reverse directions for prerequisite guide #2

Raymond

Membro da: 11/10/2010

61 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 3-28, Regan Fall 2010 Membro di Cal Poly, Team 3-28, Regan Fall 2010

CPSU-REGAN-F10S3G28

4 Membri

9 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 8

Tutti i Tempi: 6,221