Parti

Nessuna parte richiesta.

Using a Phillips #00 screwdriver, remove the four 1.1mm long screws from the top side.
  • Using a Phillips #00 screwdriver, remove the four 1.1mm long screws from the top side.

Aggiungi Commento

Using a Phillips #00 screwdriver, remove the four 1.1mm long screws from the bottom side.
  • Using a Phillips #00 screwdriver, remove the four 1.1mm long screws from the bottom side.

  • Remove the warranty sticker across the bottom.

Aggiungi Commento

Gently lift off the back and front casing. The outer shell should easily come apart.
  • Gently lift off the back and front casing.

  • The outer shell should easily come apart.

Aggiungi Commento

Make sure the device screen is face down.
  • Make sure the device screen is face down.

Aggiungi Commento

Using the plastic opening tool, wedge the tool underneath the bottom left edge of the hard drive. Raise the bottom edge of the hard drive 15 degrees up from the device. Raise the bottom edge of the hard drive 15 degrees up from the device.
  • Using the plastic opening tool, wedge the tool underneath the bottom left edge of the hard drive.

  • Raise the bottom edge of the hard drive 15 degrees up from the device.

Aggiungi Commento

Place fingers on the IDE connectors and  gently slide the hard drive out from the   IDE module. Place fingers on the IDE connectors and  gently slide the hard drive out from the   IDE module. Place fingers on the IDE connectors and  gently slide the hard drive out from the   IDE module.
  • Place fingers on the IDE connectors and gently slide the hard drive out from the IDE module.

Aggiungi Commento

Using the Phillips #00 screwdriver, unscrew the two 1.5mm long screws holding the IDE connector to the motherboard. Using the Phillips #00 screwdriver, unscrew the two 1.5mm long screws holding the IDE connector to the motherboard.
  • Using the Phillips #00 screwdriver, unscrew the two 1.5mm long screws holding the IDE connector to the motherboard.

Aggiungi Commento

Using the Phillips #00 screwdriver, unscrew the three 1.5mm long screws on the metal bracket.
  • Using the Phillips #00 screwdriver, unscrew the three 1.5mm long screws on the metal bracket.

Aggiungi Commento

Using the plastic opening tool, completely lift the metal bracket off of the motherboard. Using the plastic opening tool, completely lift the rubber insulator off of the motherboard.
  • Using the plastic opening tool, completely lift the metal bracket off of the motherboard.

  • Using the plastic opening tool, completely lift the rubber insulator off of the motherboard.

Aggiungi Commento

Using the plastic opening tool, completely lift the ribbon off of the motherboard.
  • Using the plastic opening tool, completely lift the ribbon off of the motherboard.

Aggiungi Commento

Completely remove the IDE connector from the device. The audio jack is attached to the IDE connector.  Pull at a 45 degree angle from the audio jack.
  • Completely remove the IDE connector from the device.

  • The audio jack is attached to the IDE connector. Pull at a 45 degree angle from the audio jack.

Aggiungi Commento

Using the plastic opening tool, wedge the tool underneath the top edge of the motherboard. Completely remove the motherboard.
  • Using the plastic opening tool, wedge the tool underneath the top edge of the motherboard.

  • Completely remove the motherboard.

  • The motherboard should slide out easily.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Ryan Sutardji

Membro da: 29/06/2012

171 Reputazione

7 Guide realizzate

Team

Cal Poly, Team 1-4, Regan SU 2012 Membro di Cal Poly, Team 1-4, Regan SU 2012

CPSU-REGAN-SU12S1G4

4 Membri

7 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 815