Introduzione

Use this guide to replace the power supply board of the device. This includes detaching the power cables connected to the logic board, which requires desoldering.

Lay the device on its back, and rotate so the base is facing away from you.
  • Lay the device on its back, and rotate so the base is facing away from you.

Aggiungi Commento

Grip the frame with your fingers under the edge of the frame, and thumbs pushing down on the front of the device.
  • Grip the frame with your fingers under the edge of the frame, and thumbs pushing down on the front of the device.

Aggiungi Commento

Lift up the frame with your fingers and push down the rest of the device with your thumbs.
  • Lift up the frame with your fingers and push down the rest of the device with your thumbs.

Aggiungi Commento

Remove the frame and matte from the device.
  • Remove the frame and matte from the device.

Aggiungi Commento

Remove the four 7mm Torx T6 screws.
  • Remove the four 7mm Torx T6 screws.

Aggiungi Commento

Using the plastic opening tool or your fingers, lift up the frame from any edge. Remove the frame from the device.
  • Using the plastic opening tool or your fingers, lift up the frame from any edge.

  • Remove the frame from the device.

Aggiungi Commento

Unplug the cable connecting the display to the power supply using the flat end of the spudger to pry the connector away from the circuit board. Alternate applying pressure to the left and right side of the connector to ensure that it does not break. Alternate applying pressure to the left and right side of the connector to ensure that it does not break.
  • Unplug the cable connecting the display to the power supply using the flat end of the spudger to pry the connector away from the circuit board.

  • Alternate applying pressure to the left and right side of the connector to ensure that it does not break.

Aggiungi Commento

Remove the four 7mm Torx T6 screws.
  • Remove the four 7mm Torx T6 screws.

Aggiungi Commento

Lift up the display from the left edge and flip display over. Do not lift the display too quickly, as the display is still connected to the main circuit board on the right.
  • Lift up the display from the left edge and flip display over.

  • Do not lift the display too quickly, as the display is still connected to the main circuit board on the right.

Aggiungi Commento

Use the spudger to disconnect the ribbon cable from the display by the black pins away from the connector. There is a pin on either side of the connector. Once both pins are released, the ribbon cable should slide easily out. It may be easier if someone else holds the display so the cable does not get ripped out.
  • Use the spudger to disconnect the ribbon cable from the display by the black pins away from the connector. There is a pin on either side of the connector.

  • Once both pins are released, the ribbon cable should slide easily out.

  • It may be easier if someone else holds the display so the cable does not get ripped out.

Aggiungi Commento

Remove the display assembly from the device.
  • Remove the display assembly from the device.

Aggiungi Commento

Remove the four 7mm Torx T6 screws.
  • Remove the four 7mm Torx T6 screws.

Aggiungi Commento

Desolder the 3 wires attached to the board. Remove the power supply board from the device.
  • Desolder the 3 wires attached to the board.

  • Remove the power supply board from the device.

  • The wires shown were not actually desoldered, but the board will now be separated from the rest of the device.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Casey Glasgow

Membro da: 26/01/2014

510 Reputazione

5 Guide realizzate

Team

Cal Poly, Team 9-25, Maness Winter 2014 Membro di Cal Poly, Team 9-25, Maness Winter 2014

CPSU-MANESS-W14S9G25

4 Membri

5 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 75