Aggiusta la tua roba Comunità Store

Ceiva LF2003 Display Replacement

Introduzione

Replacing the display on this device is not very difficult. A couple sets of screws and wires are all that need removing, but don't rush or you might rip a cable.

Cosa ti serve

  1. Ceiva LF2003 Display Replacement, Exterior Frame and Matting: passo 1, immagine 1 di 1

    • Lay the device on its back, and rotate so the base is facing away from you.

    Traduci

  2. Ceiva LF2003 Display Replacement: passo 2, immagine 1 di 1

    • Grip the frame with your fingers under the edge of the frame, and thumbs pushing down on the front of the device.

    Traduci

  3. Ceiva LF2003 Display Replacement: passo 3, immagine 1 di 1

    • Lift up the frame with your fingers and push down the rest of the device with your thumbs.

    Traduci

  4. Ceiva LF2003 Display Replacement: passo 4, immagine 1 di 1

    • Remove the frame and matte from the device.

    Traduci

  6. Ceiva LF2003 Display Replacement, Internal Plastic Screen Frame: passo 5, immagine 1 di 1

    • Remove the four 7mm Torx T6 screws.

    Traduci

  7. Ceiva LF2003 Display Replacement: passo 6, immagine 1 di 2 Ceiva LF2003 Display Replacement: passo 6, immagine 2 di 2

    • Using the plastic opening tool or your fingers, lift up the frame from any edge.

    • Remove the frame from the device.

    Traduci

  8. Ceiva LF2003 Display Replacement, Display: passo 7, immagine 1 di 3 Ceiva LF2003 Display Replacement, Display: passo 7, immagine 2 di 3 Ceiva LF2003 Display Replacement, Display: passo 7, immagine 3 di 3

    • Unplug the cable connecting the display to the power supply using the flat end of the spudger to pry the connector away from the circuit board.

    • Alternate applying pressure to the left and right side of the connector to ensure that it does not break.

    Traduci

  9. Ceiva LF2003 Display Replacement: passo 8, immagine 1 di 1

    • Remove the four 7mm Torx T6 screws.

    Traduci

  10. Ceiva LF2003 Display Replacement: passo 9, immagine 1 di 2 Ceiva LF2003 Display Replacement: passo 9, immagine 2 di 2

    • Lift up the display from the left edge and flip display over.

    • Do not lift the display too quickly, as the display is still connected to the main circuit board on the right.

    Traduci

  11. Ceiva LF2003 Display Replacement: passo 10, immagine 1 di 3 Ceiva LF2003 Display Replacement: passo 10, immagine 2 di 3 Ceiva LF2003 Display Replacement: passo 10, immagine 3 di 3

    • Use the spudger to disconnect the ribbon cable from the display by the black pins away from the connector. There is a pin on either side of the connector.

    • Once both pins are released, the ribbon cable should slide easily out.

    • It may be easier if someone else holds the display so the cable does not get ripped out.

    Traduci

  12. Ceiva LF2003 Display Replacement: passo 11, immagine 1 di 1

    • Remove the display assembly from the device.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Autore

con 2 altri collaboratori

Casey Glasgow

Membro da: 01/26/14

510 Reputazione

5 Guide realizzate

Distintivi: 7

+4 altri distintivi

Team

Cal Poly, Team 9-25, Maness Winter 2014 Membro di Cal Poly, Team 9-25, Maness Winter 2014

CPSU-MANESS-W14S9G25

4 Membri

5 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 0

Tutti i Tempi: 134