Flip the device over to the back side.
  • Flip the device over to the back side.

Aggiungi Commento

Slide the small switch on the back to "MAIN".
  • Slide the small switch on the back to "MAIN".

Aggiungi Commento

Slide the battery cover downwards.
  • Slide the battery cover downwards.

  • Pull off the battery cover.

Aggiungi Commento

Pull the black tab to remove the battery.
  • Pull the black tab to remove the battery.

Aggiungi Commento

Using the Phillips #00 screwdriver, remove the two screws near the top of the device.
  • Using the Phillips #00 screwdriver, remove the two screws near the top of the device.

Aggiungi Commento

Using the Phillips #00 screwdriver, remove the two screws located inside the battery compartment.
  • Using the Phillips #00 screwdriver, remove the two screws located inside the battery compartment.

Aggiungi Commento

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Partially separate the two halves of the case by inserting the tip of a small flat head screw driver into the space between the halves.
  • Partially separate the two halves of the case by inserting the tip of a small flat head screw driver into the space between the halves.

Aggiungi Commento

Pry the two halves of the case apart with the small flat head screwdriver.
  • Pry the two halves of the case apart with the small flat head screwdriver.

Aggiungi Commento

Caution: be careful not to pull out the wires connecting the two halves of the outer case. These wires are necessary for the device to be able to function.
  • Caution: be careful not to pull out the wires connecting the two halves of the outer case. These wires are necessary for the device to be able to function.

  • Lay the two halves of the outer case next to the central components as shown.

Aggiungi Commento

Using the #00 Phillips screwdriver, remove the screws from the corners of the screen. There are 3 screws total.
  • Using the #00 Phillips screwdriver, remove the screws from the corners of the screen. There are 3 screws total.

Aggiungi Commento

Lift the tab on the motherboard and pull out the ribbon cable. After the ribbon cable is detached from the motherboard, the touch screen is completely separated from the device.
  • Lift the tab on the motherboard and pull out the ribbon cable.

  • After the ribbon cable is detached from the motherboard, the touch screen is completely separated from the device.

Aggiungi Commento

Locate the small grey ribbon cable towards the bottom of the device. It should be located above the battery slot. Pinch both sides of the ribbon cable and pull it out.
  • Locate the small grey ribbon cable towards the bottom of the device. It should be located above the battery slot. Pinch both sides of the ribbon cable and pull it out.

Aggiungi Commento

Locate the multicolored wire on the motherboard near the battery compartment. Pull on the wire by the base and lift to remove.
  • Locate the multicolored wire on the motherboard near the battery compartment. Pull on the wire by the base and lift to remove.

Aggiungi Commento

Use the Phillips #00 Screwdriver to remove the two screws from the green circuit board on the back case.
  • Use the Phillips #00 Screwdriver to remove the two screws from the green circuit board on the back case.

Aggiungi Commento

Remove the the three screws on the motherboard that are shown using the Phillips #00 Screwdriver.
  • Remove the the three screws on the motherboard that are shown using the Phillips #00 Screwdriver.

Aggiungi Commento

Caution: do not break ribbon cables from the motherboard because this may cause damage to your device.
  • Caution: do not break ribbon cables from the motherboard because this may cause damage to your device.

  • Flip the motherboard towards the front cover to expose the ribbon cables underneath.

Aggiungi Commento

Locate the two ribbon cables on the motherboard. Select one to remove first and then pinch either side of it and pull out to remove the ribbon cable. Do the same for the second. Locate the two ribbon cables on the motherboard. Select one to remove first and then pinch either side of it and pull out to remove the ribbon cable. Do the same for the second.
  • Locate the two ribbon cables on the motherboard. Select one to remove first and then pinch either side of it and pull out to remove the ribbon cable. Do the same for the second.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Ryan Fernandez

Membro da: 03/04/2012

47 Reputazione

5 Guide realizzate

Team

Cal Poly, Team 5-4, Forte Spring 2012 Membro di Cal Poly, Team 5-4, Forte Spring 2012

CPSU-FORTE-S12S5G4

6 Membri

5 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 5

Tutti i Tempi: 761