Parti

Nessuna parte richiesta.

Remove the two screws from the side panel closest to the camera lens. Note: These screws are 2.9 mm long.
  • Remove the two screws from the side panel closest to the camera lens.

  • Note: These screws are 2.9 mm long.

Aggiungi Commento

Remove the two screws from the camera bottom panel.
  • Remove the two screws from the camera bottom panel.

  • Note: These screws are 2.9 mm long.

Aggiungi Commento

Remove the 2 screws from the side panel farthest from the lens.
  • Remove the 2 screws from the side panel farthest from the lens.

  • Note: These screws are 2.9 mm long.

Aggiungi Commento

Pull the back panel away from the camera body, starting at the end with the function buttons.
  • Pull the back panel away from the camera body, starting at the end with the function buttons.

Aggiungi Commento

Remove the small cover panel and attached wrist strap mount.
  • Remove the small cover panel and attached wrist strap mount.

Aggiungi Commento

Remove the front cover by gently pulling it away from the camera body.
  • Remove the front cover by gently pulling it away from the camera body.

Aggiungi Commento

Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.
  • Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

Aggiungi Commento

Remove the 2 screws located at the top of the LCD panel.
  • Remove the 2 screws located at the top of the LCD panel.

  • Note: These screws are 2.4 mm long.

Aggiungi Commento

Pull up the metal frame surrounding LCD screen starting at the side of the camera. Pull up the metal frame surrounding LCD screen starting at the side of the camera.
  • Pull up the metal frame surrounding LCD screen starting at the side of the camera.

Aggiungi Commento

Push the metal frame away from the metal tab using the spudger, to detach the frame.
  • Push the metal frame away from the metal tab using the spudger, to detach the frame.

  • Rotate the metal frame upwards.

  • Note: The metal framing should be attached by a metal tab towards the bottom of the camera, near the function buttons.

Aggiungi Commento

Carefully lift the metal frame from the camera. Remove the black LCD screen, leaving the thin lens pieces in place.
  • Carefully lift the metal frame from the camera.

  • Remove the black LCD screen, leaving the thin lens pieces in place.

  • Note: BE CAREFUL, both components are attached by an orange connector ribbon and cannot be removed yet!

Aggiungi Commento

Carefully pull on the orange connector ribbon to disconnect the LCD screen. The LCD screen can be pulled out of the frame before disconnecting its connector ribbon. Note: Tweezers are helpful to disconnect the ribbon
  • Carefully pull on the orange connector ribbon to disconnect the LCD screen.

  • The LCD screen can be pulled out of the frame before disconnecting its connector ribbon.

  • Note: Tweezers are helpful to disconnect the ribbon

Aggiungi Commento

Remove the metal frame on the side closest to the flash mechanism. This will  expose the screw securing the flash assembly. Remove the metal frame on the side closest to the flash mechanism. This will  expose the screw securing the flash assembly.
  • Remove the metal frame on the side closest to the flash mechanism. This will expose the screw securing the flash assembly.

Aggiungi Commento

Remove the screw securing the flash assembly.
  • Remove the screw securing the flash assembly.

  • Note: The screw is 2.4mm long.

Aggiungi Commento

Use the spudger to carefully disconnect the flash assembly ribbon from the black connector lock.
  • Use the spudger to carefully disconnect the flash assembly ribbon from the black connector lock.

Aggiungi Commento

Remove the flash assembly. Note: BE CAREFUL, when handling the flash assembly; touching the capacitor (the black cylinder) could shock you
  • Remove the flash assembly.

  • Note: BE CAREFUL, when handling the flash assembly; touching the capacitor (the black cylinder) could shock you

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Phillip Phung

Membro da: 19/01/2012

486 Reputazione

9 Guide realizzate

Team

Cal Poly, Team 8-18, Maness Winter 2012 Membro di Cal Poly, Team 8-18, Maness Winter 2012

CPSU-MANESS-W12S8G18

4 Membri

10 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 1

Tutti i Tempi: 2,399