Introduzione

Please complete the dis-assembly guide before attempting to install new data ports, as it is a prerequisite.

Use this guide to replace a broken data port to get your USB and card readers back.

Remove the following two Phillips screws: Two 7.85 mm Phillips #1 screws
  • Remove the following two Phillips screws:

    • Two 7.85 mm Phillips #1 screws

Aggiungi Commento

Pull the back cover off by lifting up on the cover.
  • Pull the back cover off by lifting up on the cover.

    • You may need to pull firmly as it requires quite a bit of force.

Aggiungi Commento

Open the front tray.
  • Open the front tray.

Aggiungi Commento

Lift the scanner compartment.
  • Lift the scanner compartment.

Aggiungi Commento

After opening up the scanner compartment, make sure the blue lever locks into place, keeping the compartment open.
  • After opening up the scanner compartment, make sure the blue lever locks into place, keeping the compartment open.

Aggiungi Commento

Push the blue lever back while twisting it clockwise in order to remove the lever from its slot. After removing the lever, close the scanner compartment and the scanner cover.
  • Push the blue lever back while twisting it clockwise in order to remove the lever from its slot.

  • After removing the lever, close the scanner compartment and the scanner cover.

Aggiungi Commento

Use the plastic opening tool to pry open the side cover. Use the plastic opening tool to pry open the side cover.
  • Use the plastic opening tool to pry open the side cover.

Aggiungi Commento

Flip the printer so that you are facing the underside. Use the plastic opening tool to remove the corner of the side panel from the pin.
  • Flip the printer so that you are facing the underside.

  • Use the plastic opening tool to remove the corner of the side panel from the pin.

    • Plastic pin.

Aggiungi Commento

Using the plastic opening tool, remove the side panel by loosening it from the bottom of the printer. Using the plastic opening tool, remove the side panel by loosening it from the bottom of the printer.
  • Using the plastic opening tool, remove the side panel by loosening it from the bottom of the printer.

Aggiungi Commento

Using the plastic opening tool, pry off the top cover of the LCD assembly (within the red box in the first picture). Pry around the front and side edges for the easiest removal.
  • Using the plastic opening tool, pry off the top cover of the LCD assembly (within the red box in the first picture).

    • Pry around the front and side edges for the easiest removal.

Aggiungi Commento

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
After removing the top cover of the LCD assembly, remove the LCD using the plastic opening tool.
  • After removing the top cover of the LCD assembly, remove the LCD using the plastic opening tool.

Aggiungi Commento

Completely remove the LCD by disconnecting the ribbon cable from the LCD with a gentle pull.
  • Completely remove the LCD by disconnecting the ribbon cable from the LCD with a gentle pull.

Aggiungi Commento

Locate the buttons on the printer.
  • Locate the buttons on the printer.

Aggiungi Commento

Using the plastic opening tool, gently pry around the button cover to remove it from its fixture.
  • Using the plastic opening tool, gently pry around the button cover to remove it from its fixture.

Aggiungi Commento

Remove the following five Philips screws: Five 7.65 mm Philips #1 screws
  • Remove the following five Philips screws:

    • Five 7.65 mm Philips #1 screws

Aggiungi Commento

Using the plastic opening tool, gently pry around the cover behind the LCD Screen to remove it from its fixture. Using the plastic opening tool, gently pry around the cover behind the LCD Screen to remove it from its fixture.
  • Using the plastic opening tool, gently pry around the cover behind the LCD Screen to remove it from its fixture.

Aggiungi Commento

Remove the two screws using the Phillips #1 screwdriver. Two 7.8 mm Phillips #1 screws
  • Remove the two screws using the Phillips #1 screwdriver.

    • Two 7.8 mm Phillips #1 screws

Aggiungi Commento

Gently pull the LCD screen up to remove it from its fixture.
  • Gently pull the LCD screen up to remove it from its fixture.

Aggiungi Commento

Use the plastic opening tool to pry off the plastic button assembly.
  • Use the plastic opening tool to pry off the plastic button assembly.

Aggiungi Commento

Gently pull the plastic button assembly up to remove it.
  • Gently pull the plastic button assembly up to remove it.

    • The plastic button assembly has a ribbon cable connected on the bottom, so make sure to be careful pulling it.

Aggiungi Commento

Remove the ribbon cable connected to the backside of the plastic button assembly.
  • Remove the ribbon cable connected to the backside of the plastic button assembly.

Aggiungi Commento

Remove the seven screws using the Phillips #1 screwdriver. Seven 8.7 mm Phillips #1 screws
  • Remove the seven screws using the Phillips #1 screwdriver.

    • Seven 8.7 mm Phillips #1 screws

Aggiungi Commento

Locate the spring that holds the PCB in place on the bottom left of the plastic button assembly. Gently lift the spring and pull the board out of its plastic button assembly. Gently lift the spring and pull the board out of its plastic button assembly.
  • Locate the spring that holds the PCB in place on the bottom left of the plastic button assembly.

  • Gently lift the spring and pull the board out of its plastic button assembly.

Aggiungi Commento

Remove the buttons from the plastic button assembly.
  • Remove the buttons from the plastic button assembly.

    • Buttons

Aggiungi Commento

Remove the screw using the Phillips #1 screwdriver. 7.5 mm Phillips #1 screw
  • Remove the screw using the Phillips #1 screwdriver.

    • 7.5 mm Phillips #1 screw

Aggiungi Commento

Remove the five screws using the Phillips #1 screwdriver. Five 3.5 mm Phillips #1 screws
  • Remove the five screws using the Phillips #1 screwdriver.

    • Five 3.5 mm Phillips #1 screws

Aggiungi Commento

Remove the small plastic clip using the spudger.
  • Remove the small plastic clip using the spudger.

    • Small plastic clip

Aggiungi Commento

Pull plastic inserts out of the holes in the top and bottom.
  • Pull plastic inserts out of the holes in the top and bottom.

    • Top and bottom plastic inserts

Aggiungi Commento

Completely remove the board from the printer by pulling the board towards the back of the printer.
  • Completely remove the board from the printer by pulling the board towards the back of the printer.

    • This requires effort and time as the board comes out little by little.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Steven MacLean

Membro da: 14/01/2013

74 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 19-41, Regan Winter 2013 Membro di Cal Poly, Team 19-41, Regan Winter 2013

CPSU-REGAN-W13S19G41

4 Membri

6 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 11

Tutti i Tempi: 1,503