Introduzione

This fix is safe and only requires a screwdriver.

Parti

Nessuna parte richiesta.

Remove the two 4.8 mm black screws above the lens on the front of the camera.
  • Remove the two 4.8 mm black screws above the lens on the front of the camera.

Aggiungi Commento

Remove the 4.3 mm black screw under the lens ring, and the 4.8 mm black screw under the camera.
  • Remove the 4.3 mm black screw under the lens ring, and the 4.8 mm black screw under the camera.

Aggiungi Commento

Remove the 4.8 mm black screw on the left side of the camera.
  • Remove the 4.8 mm black screw on the left side of the camera.

Aggiungi Commento

Remove the front panel by lifting it away from the camera's body.
  • Remove the front panel by lifting it away from the camera's body.

Aggiungi Commento

Remove seven 4.25 mm black screws on the bottom panel.
  • Remove seven 4.25 mm black screws on the bottom panel.

Aggiungi Commento

Remove the bottom panel.
  • Remove the bottom panel.

Aggiungi Commento

Remove two 6.5 mm black screws from the panel.
  • Remove two 6.5 mm black screws from the panel.

Aggiungi Commento

Remove the plastic remote control socket cap by pulling it straight out.
  • Remove the plastic remote control socket cap by pulling it straight out.

Aggiungi Commento

Slide panel toward bottom of camera to remove. Slide panel toward bottom of camera to remove.
  • Slide panel toward bottom of camera to remove.

Aggiungi Commento

Slide the outer eyepiece upward to remove it.
  • Slide the outer eyepiece upward to remove it.

Aggiungi Commento

Remove the two 4.75 mm black screws located  on the top of the camera.
  • Remove the two 4.75 mm black screws located on the top of the camera.

Aggiungi Commento

Remove the four 4.3 mm  black screws near the bottom corners of the eyepiece at the back of the camera.
  • Remove the four 4.3 mm black screws near the bottom corners of the eyepiece at the back of the camera.

Aggiungi Commento

Slowly separate the top panel from the camera by pushing it upward. Separating the top panel too far or quickly can damage the ribbon cable and connecting wires that are still attached to the top panel of the camera.
  • Slowly separate the top panel from the camera by pushing it upward.

  • Separating the top panel too far or quickly can damage the ribbon cable and connecting wires that are still attached to the top panel of the camera.

Aggiungi Commento

Remove the two 5.5 mm screws from front of camera.
  • Remove the two 5.5 mm screws from front of camera.

Aggiungi Commento

Remove grip panel.
  • Remove grip panel.

Aggiungi Commento

Remove one black screw from battery door on underside of grip.
  • Remove one black screw from battery door on underside of grip.

Aggiungi Commento

Remove battery door.
  • Remove battery door.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Jackie

Membro da: 17/04/2011

218 Reputazione

3 Guide realizzate

Team

Cal Poly, Team 8-8, Regan Spring 2011 Membro di Cal Poly, Team 8-8, Regan Spring 2011

CPSU-REGAN-S11S8G8

5 Membri

11 Guide realizzate

I was able to complete this by going from step 9 to 15. Oddly, I only had one screw to remove in step 15 but the grip piece easily slid out without needing to remove the top of the camera.

Alan - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 6

Ultimi 30 Giorni: 13

Tutti i Tempi: 3,104