Introduzione

This guide will provide the steps to access the internal components including the motherboard where the copper button plates are located.

On the back of the device, remove the four 3/8"  Torx head screws using the T-6 Torx bit. A Torx bit is the piece that is inserted into a bit driver, also known as a screw driver.
  • On the back of the device, remove the four 3/8" Torx head screws using the T-6 Torx bit.

  • A Torx bit is the piece that is inserted into a bit driver, also known as a screw driver.

Aggiungi Commento

Remove the stylus if it is in the housing at the top of the device. Turn the device so you are looking at it from the top down. Using your thumbs on each wall of the stylus housing, open the frame of the device by gently pulling the two sides apart.
  • Remove the stylus if it is in the housing at the top of the device.

  • Turn the device so you are looking at it from the top down.

  • Using your thumbs on each wall of the stylus housing, open the frame of the device by gently pulling the two sides apart.

Aggiungi Commento

Insert a spudger into the seam between the front and back plates of the frame. Unsnap the snaps around the entire frame of the device. Remove the front face plate by pulling it straight up. The unlock switch on the device's side might come off while undoing the internal snaps or removing the face plate. This is perfectly normal.
  • Insert a spudger into the seam between the front and back plates of the frame. Unsnap the snaps around the entire frame of the device.

  • Remove the front face plate by pulling it straight up.

  • The unlock switch on the device's side might come off while undoing the internal snaps or removing the face plate. This is perfectly normal.

Aggiungi Commento

Use a spudger (or gently bend the back plate of the device) to unsnap the snaps holding the screen in place. Use a spudger (or gently bend the back plate of the device) to unsnap the snaps holding the screen in place.
  • Use a spudger (or gently bend the back plate of the device) to unsnap the snaps holding the screen in place.

Aggiungi Commento

With a spudger, press against the lip of the connector closest to the wires to remove the battery connector from the motherboard. With a spudger, press against the lip of the connector closest to the wires to remove the battery connector from the motherboard.
  • With a spudger, press against the lip of the connector closest to the wires to remove the battery connector from the motherboard.

Aggiungi Commento

Gently lift the motherboard with a spudger or small object by inserting it in the seam between the back frame and the motherboard. Remove the battery hidden behind the motherboard.
  • Gently lift the motherboard with a spudger or small object by inserting it in the seam between the back frame and the motherboard.

  • Remove the battery hidden behind the motherboard.

Aggiungi Commento

Using tweezers gently go around the edges of the copper plate to remove the adhesive. Using tweezers gently go around the edges of the copper plate to remove the adhesive.
  • Using tweezers gently go around the edges of the copper plate to remove the adhesive.

Aggiungi Commento

Use tweezers to grip the outer edge of the copper plate and lift the button straight off. Use tweezers to grip the outer edge of the copper plate and lift the button straight off.
  • Use tweezers to grip the outer edge of the copper plate and lift the button straight off.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Gareth

Membro da: 09/09/2014

364 Reputazione

3 Guide realizzate

Team

CSU Fullerton, Team 2-6, Bruce Fall 2014 Membro di CSU Fullerton, Team 2-6, Bruce Fall 2014

CSUF-BRUCE-F14S2G6

4 Membri

3 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 7

Tutti i Tempi: 2,056