Introduzione

This guide was written to aid with Blackberry Curve screen replacement. Following the steps below should provide relatively simple means of achieving this goal.

Place your Blackberry face down in front of you.
  • Place your Blackberry face down in front of you.

Aggiungi Commento

Locate the indent on the bottom of the back cover.
  • Locate the indent on the bottom of the back cover.

  • Use your fingernail to lift and remove the back cover.

Aggiungi Commento

From the top, use your fingernail to lift and remove the battery.
  • From the top, use your fingernail to lift and remove the battery.

Aggiungi Commento

Use the T6 Torx screwdriver to unscrew the two 5mm screws highlighted.
  • Use the T6 Torx screwdriver to unscrew the two 5mm screws highlighted.

Aggiungi Commento

Place the phone face up and use tweezers to securely grip and lift the screen upwards. Place the phone face up and use tweezers to securely grip and lift the screen upwards.
  • Place the phone face up and use tweezers to securely grip and lift the screen upwards.

Aggiungi Commento

Use your prying tool to lift the bottom edge of the front cover.
  • Use your prying tool to lift the bottom edge of the front cover.

Aggiungi Commento

Use your nails to unclip sides of frame from the phone.
  • Use your nails to unclip sides of frame from the phone.

Aggiungi Commento

Lift and remove frame.
  • Lift and remove frame.

Aggiungi Commento

Lift and remove keyboard.
  • Lift and remove keyboard.

Aggiungi Commento

Locate and remove the two 5mm screws on top of keyboard base using the T6 Torx screwdriver
  • Locate and remove the two 5mm screws on top of keyboard base using the T6 Torx screwdriver

Aggiungi Commento

Carefully pull keyboard base up and away from phone.
  • Carefully pull keyboard base up and away from phone.

  • Disconnect keyboard base from phone completely.

Aggiungi Commento

Locate and remove the four 5mm screws on the top and bottom of phone using the T6 Torx screwdriver Locate and remove the four 5mm screws on the top and bottom of phone using the T6 Torx screwdriver Locate and remove the four 5mm screws on the top and bottom of phone using the T6 Torx screwdriver
  • Locate and remove the four 5mm screws on the top and bottom of phone using the T6 Torx screwdriver

Aggiungi Commento

Using a prying tool, find the crease below the screen. Insert where shown and use the tool to unclip the two sides of screen from body.
  • Using a prying tool, find the crease below the screen.

  • Insert where shown and use the tool to unclip the two sides of screen from body.

    • Prying tool goes approximately midway between the top and bottom edge of the screen.

Aggiungi Commento

From back of the phone, use finger to push the front piece of the phone away from the back piece. From back of the phone, use finger to push the front piece of the phone away from the back piece.
  • From back of the phone, use finger to push the front piece of the phone away from the back piece.

Aggiungi Commento

Using a prying tool, detach the ribbon cable from the top left corner of the screen and remove from phone. Using a prying tool, detach the ribbon cable from the top left corner of the screen and remove from phone. Using a prying tool, detach the ribbon cable from the top left corner of the screen and remove from phone.
  • Using a prying tool, detach the ribbon cable from the top left corner of the screen and remove from phone.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 8 persone hanno completato questa guida.

Alek Squires

Membro da: 30/09/2013

415 Reputazione

2 Guide realizzate

Team

Cal Poly, Team 14-7, Forte Fall 2013 Membro di Cal Poly, Team 14-7, Forte Fall 2013

CPSU-FORTE-F13S14G7

5 Membri

5 Guide realizzate

would appreciate new ldc part # and order info! - - !

Donald Burgo - Replica

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 22

Tutti i Tempi: 3,547