Introduzione

If you are removing or replacing the Blackberry 7520 LCD screen, look here for support.

Parti

Nessuna parte richiesta.

Turn the phone upside down. Push down on the black button on the back of the phone to slide the rear panel off.
  • Turn the phone upside down.

  • Push down on the black button on the back of the phone to slide the rear panel off.

  • The battery should be visible now.

Aggiungi Commento

Hold the BlackBerry in one hand face-up with the screen facing towards you. Gently smack the phone against your hand to dislodge the battery. Gently smack the phone against your hand to dislodge the battery.
  • Hold the BlackBerry in one hand face-up with the screen facing towards you.

  • Gently smack the phone against your hand to dislodge the battery.

Aggiungi Commento

Use a T6 Torx screwdriver to remove the 6 screws holding the rear of the phone. Use a T6 Torx screwdriver to remove the 6 screws holding the rear of the phone.
  • Use a T6 Torx screwdriver to remove the 6 screws holding the rear of the phone.

Aggiungi Commento

Use a pick or small tool to push the clips holding the rear away from you. Applying too much pressure could break the plastic clips and permanently damage your Blackberry.
  • Use a pick or small tool to push the clips holding the rear away from you.

  • Applying too much pressure could break the plastic clips and permanently damage your Blackberry.

Aggiungi Commento

Repeat the process of unlatching the clips for the top section of the Blackberry.
  • Repeat the process of unlatching the clips for the top section of the Blackberry.

Aggiungi Commento

Slide the rear panel forward to reveal the logic board. Slide the rear panel forward to reveal the logic board.
  • Slide the rear panel forward to reveal the logic board.

Aggiungi Commento

Remove the indicated screws using a T6 Torx screwdriver. Remove the indicated screws using a T6 Torx screwdriver.
  • Remove the indicated screws using a T6 Torx screwdriver.

Aggiungi Commento

Remove the logic board. Remove the indicated screw using the T6 Torx screwdriver.
  • Remove the logic board.

  • Remove the indicated screw using the T6 Torx screwdriver.

Aggiungi Commento

Pull the metal plate away from the front panel of the cell phone. Pull the metal plate away from the front panel of the cell phone.
  • Pull the metal plate away from the front panel of the cell phone.

Aggiungi Commento

Place the faceplate face-down and the interior of the phone face-up, as shown.
  • Place the faceplate face-down and the interior of the phone face-up, as shown.

Aggiungi Commento

Turn the phone so that it faces towards you.
  • Turn the phone so that it faces towards you.

Aggiungi Commento

Use a pick or other small tool to pop the small plastic clip holding the LCD panel on
  • Use a pick or other small tool to pop the small plastic clip holding the LCD panel on

Aggiungi Commento

Pull the LCD screen off of the board. Pull the LCD screen off of the board.
  • Pull the LCD screen off of the board.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Nathan

Membro da: 18/01/2010

31 Reputazione

7 Guide realizzate

Team

Cal Poly, Team 5-7, Forte Winter 2010 Membro di Cal Poly, Team 5-7, Forte Winter 2010

CPSU-FORTE-W10S5G7

5 Membri

7 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 3

Tutti i Tempi: 1,329