Open the battery door by sliding the tab on the battery door while pushing the battery door away from the camera. Remove batteries.
  • Open the battery door by sliding the tab on the battery door while pushing the battery door away from the camera.

  • Remove batteries.

Aggiungi Commento

Remove the three indicated .2mm screws using a Philips #00 screwdriver. Gently pull off side-panel to remove it.
  • Remove the three indicated .2mm screws using a Philips #00 screwdriver.

  • Gently pull off side-panel to remove it.

Aggiungi Commento

Remove the two indicated .2mm screws using a Philips #00 screwdriver.
  • Remove the two indicated .2mm screws using a Philips #00 screwdriver.

Aggiungi Commento

Remove the indicated .2mm screw using a Philips #00 screwdriver. Remove the three .2mm screws located on the internal side of the top panel within the battery chamber using a Philips #00 screwdriver.
  • Remove the indicated .2mm screw using a Philips #00 screwdriver.

  • Remove the three .2mm screws located on the internal side of the top panel within the battery chamber using a Philips #00 screwdriver.

Aggiungi Commento

Open 'DIGITAL A/V OUT' door on camera. Remove the two indicated .2mm screws using a Philips #00 screwdriver.
  • Open 'DIGITAL A/V OUT' door on camera.

  • Remove the two indicated .2mm screws using a Philips #00 screwdriver.

Aggiungi Commento

Grip the sides of the top panel and gently pull to separate the top panel from the camera body.
  • Grip the sides of the top panel and gently pull to separate the top panel from the camera body.

  • The top panel will not completely detach.

Aggiungi Commento

Gently pull the front and back panels apart, and use a Phillips #00 screwdriver to remove the screw connecting the panels. Gripping the top and bottom, gently pull the front panel away from the camera body to remove it.
  • Gently pull the front and back panels apart, and use a Phillips #00 screwdriver to remove the screw connecting the panels.

  • Gripping the top and bottom, gently pull the front panel away from the camera body to remove it.

Aggiungi Commento

Use the spudger to gently pull back the retaining clip and pull the ribbon out. The top panel should now be completely detached from the camera.
  • Use the spudger to gently pull back the retaining clip and pull the ribbon out.

  • The top panel should now be completely detached from the camera.

  • Applying too much force to the spudger may damage the retaining clip.

FAIL… slide the black element under the ribbon.

marekzy - Replica

Remove .2 mm screw using a #00 Philips screwdriver. Gently pry off back panel to remove it.
  • Remove .2 mm screw using a #00 Philips screwdriver.

  • Gently pry off back panel to remove it.

Aggiungi Commento

Remover .2 mm screw using a #00 Philips screwdriver.
  • Remover .2 mm screw using a #00 Philips screwdriver.

Aggiungi Commento

Using tweezers, gently pull remove the small rod in the battery door hinge. Using tweezers, gently pull remove the small rod in the battery door hinge.
  • Using tweezers, gently pull remove the small rod in the battery door hinge.

Aggiungi Commento

Gently pull up on the battery door to remove it. Gently pull up on the battery door to remove it.
  • Gently pull up on the battery door to remove it.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Un'altra persona ha completato questa guida.

Alicia Burns

Membro da: 13/10/2014

552 Reputazione

5 Guide realizzate

Team

Clemson, Team 2-5, Benson Fall 2014 Membro di Clemson, Team 2-5, Benson Fall 2014

CLEM-BENSON-F14S2G5

4 Membri

9 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 2

Ultimi 30 Giorni: 10

Tutti i Tempi: 462