Introduzione

You will do this after you have taken out the hard drive.

Parti

Nessuna parte richiesta.

Pull the keyboard tabs toward you while lifting up on the keyboard until it releases from it's hold.
  • Pull the keyboard tabs toward you while lifting up on the keyboard until it releases from it's hold.

  • To lift the keyboard out pull it up and away from you. Then place the keyboard on the track pad.

Aggiungi Commento

Pull the keyboard ribbon vertically from the logic board to release connection.
  • Pull the keyboard ribbon vertically from the logic board to release connection.

  • The connector may be tight and difficult to remove. If stuck try rocking the connector back and forth while pulling up until it releases. This same process can be used for many of the connectors on this device.

  • Remove battery and CD/DVD drives before proceeding any further.

Aggiungi Commento

Your computer should look approximately like this.
  • Your computer should look approximately like this.

Aggiungi Commento

Remove the two silver Phillips #1 screws that attach the heat shield to the metal framework.
  • Remove the two silver Phillips #1 screws that attach the heat shield to the metal framework.

  • Lift the heat shield up and toward you.

Aggiungi Commento

Pull the PRAM battery cable vertically upward to disconnect it.
  • Pull the PRAM battery cable vertically upward to disconnect it.

  • Remove the battery by pulling up and to the left.

Aggiungi Commento

Remove the two T8 Torx screws that attach the heat sink to the processor.
  • Remove the two T8 Torx screws that attach the heat sink to the processor.

  • Remove the long silver Phillips #1 screw from the heat sink.

Aggiungi Commento

Lift up the heat sink unit from the left side and remove.
  • Lift up the heat sink unit from the left side and remove.

Aggiungi Commento

Lift the processor on the right side and pull directly up.
  • Lift the processor on the right side and pull directly up.

  • The RAM chips should be in the slots on the processor.

Aggiungi Commento

After removing the RAM, your laptop should now look like this.
  • After removing the RAM, your laptop should now look like this.

Aggiungi Commento

Guida ai regali per la festa del papà
Facciamo onore non solo ai nostri padri — festeggiamo tutti i mentori che ci hanno insegnato a riparare.
Guida ai regali per la festa del papà
Facciamo onore a chi ci ha insegnato a riparare.
Locate the orange tab, which should be just left of the hard-drive.
  • Locate the orange tab, which should be just left of the hard-drive.

  • You must disconnect this orange tab from the logic board to enable the next step.

  • It is better to do this by grabbing the plastic connection point, not the relatively flexible cable.

Aggiungi Commento

Grab the plastic strip shown here and gently remove, pulling up and left.
  • Grab the plastic strip shown here and gently remove, pulling up and left.

  • Pull left to avoid the hard drive catching the casing.

Aggiungi Commento

Once you have removed the hard-drive, your laptop should like this.
  • Once you have removed the hard-drive, your laptop should like this.

Aggiungi Commento

Remove the single black Torx screw from the modem.
  • Remove the single black Torx screw from the modem.

  • Remove the black rectangle that is being held on by the one Torx screw.

Aggiungi Commento

Using your fingers, lift the modem from the socket it is plugged into.
  • Using your fingers, lift the modem from the socket it is plugged into.

Aggiungi Commento

Disconnect the cable that is attached to the end of the modem to remove the modem.
  • Disconnect the cable that is attached to the end of the modem to remove the modem.

Aggiungi Commento

Your computer will look approximately like this.
  • Your computer will look approximately like this.

Aggiungi Commento

Push the display back.
  • Push the display back.

  • Put your index finger under the power button and gently pull the clutch cover back.

  • Repeat for the left side.

Aggiungi Commento

Lift the clutch cover up and off.  Pull it towards yourself.
  • Lift the clutch cover up and off. Pull it towards yourself.

Aggiungi Commento

Disconnect the display cable from the logic board.
  • Disconnect the display cable from the logic board.

Aggiungi Commento

Remove the Torx screw that holds the display cable.
  • Remove the Torx screw that holds the display cable.

  • Pull out thick display inverter board by pulling it up and out. Two tabs will be holding it in place, you need to get pass these to pull the board free.

Aggiungi Commento

Disconnect the white inverter cable.  Pull it towards the left.
  • Disconnect the white inverter cable. Pull it towards the left.

Aggiungi Commento

Disconnect the inverter plug by pulling it up from the logib board.
  • Disconnect the inverter plug by pulling it up from the logib board.

Aggiungi Commento

Turn the laptop around.
  • Turn the laptop around.

  • Open the port door.

  • Remove the four Torx screws.

Aggiungi Commento

Turn the laptop so the front faces you.
  • Turn the laptop so the front faces you.

  • Pull the black Airport antenna up.

Aggiungi Commento

Pull the display up as you hold it firmly with both hands.
  • Pull the display up as you hold it firmly with both hands.

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Isabelle

Membro da: 18/04/2011

11 Reputazione

1 Guida realizzata

Team

Cal Poly, Team 4-2, Regan Spring 2011 Membro di Cal Poly, Team 4-2, Regan Spring 2011

CPSU-REGAN-S11S4G2

4 Membri

7 Guide realizzate

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 0

Ultimi 30 Giorni: 2

Tutti i Tempi: 1,228