Aggiusta la tua roba Comunità Store

Aiptek DZO-V58N Lens Protector Replacement

Introduzione

The lens protector is a plastic cover that protects the lens from scratches, dirt and other debris. Use this guide to replace the lens protector.

Cosa ti serve

  1. Aiptek DZO-V58N Lens Protector Replacement, Battery: passo 1, immagine 1 di 1

    • Locate the battery compartment on the back of the camera. It is the panel with the plastic ridges for simple removal.

    • Slide the battery compartment cover down off of the camera body.

    Traduci

  2. Aiptek DZO-V58N Lens Protector Replacement: passo 2, immagine 1 di 1

    • Pry up the battery from the bottom using a finger and remove the batter from the case.

    Traduci

  3. Aiptek DZO-V58N Lens Protector Replacement, Lens Protector: passo 3, immagine 1 di 1

    • Remove the lanyard by pulling the grey lace through the black string loop.

    • Pull black string loop through the silver bracket.

    Traduci

  4. Aiptek DZO-V58N Lens Protector Replacement: passo 4, immagine 1 di 1

    • Use a plastic opening tool to pry off the black control cover.

    • The face plates are glued, so use force to pry the face plates from the camera body.

    Traduci

  6. Aiptek DZO-V58N Lens Protector Replacement: passo 5, immagine 1 di 1

    • Use a plastic opening tool to pry off the ridged back face plate and the black button.

    • The face plates are glued, so use force to pry the face plates from the camera body.

    • The button is loose and should come off with little or no effort.

    Traduci

  7. Aiptek DZO-V58N Lens Protector Replacement: passo 6, immagine 1 di 1

    • Use a plastic opening tool to pry off the silver face plate.

    • The face plates are glued, so use force to pry the face plates from the camera body.

    Traduci

  8. Aiptek DZO-V58N Lens Protector Replacement: passo 7, immagine 1 di 3 Aiptek DZO-V58N Lens Protector Replacement: passo 7, immagine 2 di 3 Aiptek DZO-V58N Lens Protector Replacement: passo 7, immagine 3 di 3

    • Open the USB cover to expose the small machine screw.

    • Use the Phillips #00 screwdriver to unscrew the six 0.5cm machine case screws (distributed around the camera body).

    • These small screws are easy to lose. Place the removed screws in an organized container to avoid losing them.

    Traduci

  9. Aiptek DZO-V58N Lens Protector Replacement: passo 8, immagine 1 di 1

    • Pull off the side control panel.

    Traduci

  10. Aiptek DZO-V58N Lens Protector Replacement: passo 9, immagine 1 di 2 Aiptek DZO-V58N Lens Protector Replacement: passo 9, immagine 2 di 2

    • Flip open the screen by pulling the loose end of the screen away from the case.

    • Use tweezers to remove the two outside rubber dots to reveal the two 0.5cm machine screws.

    • Use the #00 Phillips Screwdriver to remove both screws.

    Traduci

  11. Aiptek DZO-V58N Lens Protector Replacement: passo 10, immagine 1 di 2 Aiptek DZO-V58N Lens Protector Replacement: passo 10, immagine 2 di 2

    • Pull the body apart from the bottom of device just enough to make space to remove the silver plastic strap holder.

    • Use tweezers to remove the silver plastic strap holder.

    • Use a plastic opening tool to pry off the lens protector.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Autore

con 3 altri collaboratori

Zachary Yun

Membro da: 04/03/12

7 Reputazione

5 Guide realizzate

Distintivi: 4

+ 1 altro distintivo

Team

Cal Poly, Team 5-5, Forte Spring 2012 Membro di Cal Poly, Team 5-5, Forte Spring 2012

CPSU-FORTE-S12S5G5

5 Membri

10 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 1

Ultimi 30 Giorni: 1

Tutti i Tempi: 554