Aggiusta la tua roba Comunità Store

1997-2003 Chevrolet Malibu Tail Lights Replacement

Introduzione

Replacing burnt out or broken bulbs is a quick and easy fix that makes your car easier to see from behind, helping to prevent accidents.

Cosa ti serve

  1. 1997-2003 Chevrolet Malibu Tail Lights Replacement, Tail Lights: passo 1, immagine 1 di 1

    • Locate the plastic casing that holds the trunk liner in place, directly behind the tail light.

    • Unscrew the plastic casings.

    Traduci

  2. 1997-2003 Chevrolet Malibu Tail Lights Replacement: passo 2, immagine 1 di 1

    • Make sure to put some pressure on the tail light itself so it does not fall out when you unscrew it.

    • Unscrew the three plastic wing nuts located behind the tail lights.

    Traduci

  3. 1997-2003 Chevrolet Malibu Tail Lights Replacement: passo 3, immagine 1 di 1

    • When the tail light assembly comes loose, do not fully remove it because it may damage the connected wires.

    • Carefully pull the tail light away from the car to expose the connected wires.

    Traduci

  5. 1997-2003 Chevrolet Malibu Tail Lights Replacement: passo 4, immagine 1 di 3 1997-2003 Chevrolet Malibu Tail Lights Replacement: passo 4, immagine 2 di 3 1997-2003 Chevrolet Malibu Tail Lights Replacement: passo 4, immagine 3 di 3

    • Unclip the rear panel of the tail light assembly. There are two clips on the top and two on the bottom.

    • Remove the rear panel from the rest of the assembly.

    Traduci

  6. 1997-2003 Chevrolet Malibu Tail Lights Replacement: passo 5, immagine 1 di 1

    • Do not pull on the bulb, handle it gently because it is fragile.

    • Grab the plastic base of the bulb and gently wiggle it free.

    Traduci

  7. 1997-2003 Chevrolet Malibu Tail Lights Replacement: passo 6, immagine 1 di 1

    • When handling the new bulbs, avoid touching the glass as much as possible because this can reduce the life of the bulb.

    • Gently push the new bulb into the plastic housing.

    Traduci

  8. 1997-2003 Chevrolet Malibu Tail Lights Replacement: passo 7, immagine 1 di 1

    • After putting the new bulbs in, turn the desired lights on to check that the newly installed bulbs work correctly.

    • These bulbs have different functions including blinkers, brake lights, hazard lights, and back-up lights. They will only turn on when the necessary signal is sent.

    Traduci
Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 4 persone hanno completato questa guida.

Autore

con 6 altri collaboratori

Sank Yang

Membro da: 10/03/12

484 Reputazione

5 Guide realizzate

Distintivi: 11

+8 altri distintivi

Team

Cal Poly, Team 9-15, Amido Fall 2012 Membro di Cal Poly, Team 9-15, Amido Fall 2012

CPSU-AMIDO-F12S9G15

4 Membri

5 Guide realizzate

0 Commenti

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 0

Ultimi 7 Giorni: 8

Ultimi 30 Giorni: 38

Tutti i Tempi: 19,379