Introduzione

A step by step guide on how to replace the speakers on a 1996 Ford Thunderbird.

Use a plastic pry tool (or screwdriver but be careful) to pop the black panel off of the door. Use a plastic pry tool (or screwdriver but be careful) to pop the black panel off of the door.
  • Use a plastic pry tool (or screwdriver but be careful) to pop the black panel off of the door.

Aggiungi Commento

Once the black panel has been removed, take out the power side mirror plug (if you have one) Once the black panel has been removed, take out the power side mirror plug (if you have one)
  • Once the black panel has been removed, take out the power side mirror plug (if you have one)

Aggiungi Commento

Begin romving the power windows connector by removing the screws, then prying off the plastic connectors
  • Begin romving the power windows connector by removing the screws, then prying off the plastic connectors

Aggiungi Commento

Remove the bolt holding on the plastic to the door. Remove the bolt holding on the plastic to the door.
  • Remove the bolt holding on the plastic to the door.

Aggiungi Commento

Pry the plastic off of the light enclosure on the bottom of the door. Once you remove it, take the screw out. This is the only other screw holding the door on. Pry the plastic off of the light enclosure on the bottom of the door. Once you remove it, take the screw out. This is the only other screw holding the door on.
  • Pry the plastic off of the light enclosure on the bottom of the door. Once you remove it, take the screw out. This is the only other screw holding the door on.

Aggiungi Commento

Now your door should look like this! (With some Ford factory duct tape)
  • Now your door should look like this! (With some Ford factory duct tape)

Aggiungi Commento

Once you've removed the speaker off of the door by removing the bolts unplug it. This is the connector
  • Once you've removed the speaker off of the door by removing the bolts unplug it. This is the connector

Aggiungi Commento

Once you solder the wires (or crimp them) replace the new speaker on to the door.
  • Once you solder the wires (or crimp them) replace the new speaker on to the door.

Aggiungi Commento

Moving to the back, use your screw driver or pry tool on the BOTTOM of the panel. Pry it outward, then pull it out. Pry it outward, then pull it out.
  • Moving to the back, use your screw driver or pry tool on the BOTTOM of the panel.

  • Pry it outward, then pull it out.

Aggiungi Commento

Remove the speaker like the driver's side (as show earlier) Unplug the speaker, solder the wires, put the bolts back on afterwards
  • Remove the speaker like the driver's side (as show earlier)

  • Unplug the speaker, solder the wires, put the bolts back on afterwards

Aggiungi Commento

Here's the passenger side door panel taken out. remove the screws and pry out like the driver's side
  • Here's the passenger side door panel taken out. remove the screws and pry out like the driver's side

Aggiungi Commento

Follow the same steps from the driver's side for the passenger's side, replace all the plastic, and enjoy! Follow the same steps from the driver's side for the passenger's side, replace all the plastic, and enjoy!
  • Follow the same steps from the driver's side for the passenger's side, replace all the plastic, and enjoy!

Aggiungi Commento

Conclusione

To reassemble your device, follow these instructions in reverse order.

Altre 2 persone hanno completato questa guida.

Kyle

Membro da: 02/09/2014

173 Reputazione

1 Guida realizzata

Aggiungi Commento

Visualizza Statistiche:

Ultime 24 Ore: 1

Ultimi 7 Giorni: 7

Ultimi 30 Giorni: 41

Tutti i Tempi: 2,923