Aggiusta le tue cose Community Store

후면 커버 분리

Avviso: Stai modificando una guida prerequisita. Tutte le modifiche avranno effetto su tutte le guide che includono questo passo.

Torna alla Guida
Inglese
Coreano
Passo precedente

Traduzione in corso passo 11

Passo 11
Back Cover Removal: passo 0, immagine 1 di 1

  • Remove the back cover.

  • To re-install the back cover:

  • Use tweezers to peel away any remaining adhesive from the phone's chassis. Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to prep the surface for the new adhesive. You don't have to clear out adhesive down to the plastic but larger pieces should be removed.

  • Turn on your phone and test your repair before installing new adhesive and resealing the phone.

  • Carefully apply the new adhesive to the back cover, then line up one edge of the glass against the phone chassis and firmly press the glass into the phone.

후면 커버를 분리하세요.

후면 커버를 설치하려면:

핀셋을 사용하여 휴대폰 섀시에 남아 있는 접착제를 제거하세요. 그 다음 (최소 90%) 고농도 이소프로필 알코올과 보풀-없는 천으로 접착 부분을 청소하여 새 접착 표면을 준비하세요.

새 접착제를 설치하고 휴대폰을 다시 닫기 전에 휴대폰을 켜고 수리를 테스트하세요.

새 접착제를 후면 커버에 조심히 바르고, 유리의 한쪽 가장자리를 휴대폰 섀시에 맞추고 유리를 휴대폰에 단단히 누르세요.

대안으로, 접착제를 교체하지 않고 후면 커버를 재설치 할 수 있습니다. 후면 커버가 평평하게 자리잡지 못하게 막는 큰 접착제 덩어리를 제거하세요. 설치하고 나서, 후면 커버를 가열하고 압력을 가하여 고정하세요. 방수는 안되지만 접착력은 충분히 강합니다.

[* black] Remove the back cover.
-[* icon_reminder] To install a back cover:
- [* black] Use tweezers to peel away any remaining adhesive from the phone's chassis. Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to prep the surface for the new adhesive.
+[* icon_reminder] To re-install the back cover:
+ [* black] Use [product|IF145-020|tweezers] to peel away any remaining adhesive from the phone's chassis. Then clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth to prep the surface for the new adhesive. You don't have to clear out adhesive down to the plastic but larger pieces should be removed.
[* black] Turn on your phone and test your repair before installing new adhesive and resealing the phone.
[* black] Carefully apply the new adhesive to the back cover, then line up one edge of the glass against the phone chassis and firmly press the glass into the phone.
- [* icon_note] Alternatively, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

I tuoi contributi sono usati su licenza in base alla licenza open source Creative Commons.