Aggiusta la tua roba

Diritto alla Riparazione

Componenti & Strumenti

Nota: Stai modificando un prerequisito per la guida che stavi visualizzando. Tutte le modifiche avranno effetto su tutte le 5guide che includono questo passo.

Torna alla Guida
Inglese
Italiano
Passaggio precedente

Traduzione in corso passo 7

Passo 7
Once you have sliced around the phone, twist an opening pick in one of the edges to help separate the back cover from the frame. Lift the back cover slowly. Use opening picks to slice any remaining adhesive. Remove the back cover.

  • Once you have sliced around the phone, twist an opening pick in one of the edges to help separate the back cover from the frame.

  • Lift the back cover slowly. Use opening picks to slice any remaining adhesive.

  • Remove the back cover.

  • During reassembly, this is a good point to power on your phone and test all functions before you seal the back cover in place. Be sure to power your phone back down completely before you continue working.

  • Follow this guide to reinstall the back cover, transfer and install the camera bezel, and replace the adhesive.

  • If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it.

Una volta tagliata la colla tutto attorno al telefono, torci un plettro di apertura in uno dei bordi per favorire il distacco della cover posteriore dalla scocca.

Solleva lentamente la cover posteriore. Usa dei plettri di apertura per tagliare tutto l'adesivo rimasto.

Rimuovi la cover posteriore.

Segui questa guida per rimontare la cover posteriore e sostituire l'adesivo.

Nel corso del rimontaggio, è una buona idea accendere il telefono e provarne tutte le funzioni prima di sigillare nuovamente in posizione la cover posteriore. Ricordati poi di spegnere nuovamente il telefono prima di continuare a lavorarci.

Se vuoi, puoi rimontare la cover posteriore senza sostituire l'adesivo. Rimuovi tutti i pezzi grossi di adesivo che potrebbero fare spessore sotto la cover posteriore. Dopo il rimontaggio, scalda la cover e premila per fissarla in posizione. Il telefono non sarà più impermeabile, ma la colla rimasta di solito basta per bloccare la cover.

[* black] Once you have sliced around the phone, twist an opening pick in one of the edges to help separate the back cover from the frame.
[* black] Lift the back cover slowly. Use opening picks to slice any remaining adhesive.
[* black] Remove the back cover.
[* icon_reminder] [guide|124003|Follow this guide|new_window=true] to reinstall the back cover and replace the adhesive.
[* icon_note] During reassembly, this is a good point to power on your phone and test all functions before you seal the back cover in place. Be sure to power your phone back down completely before you continue working.
[* icon_reminder] [guide|124003|Follow this guide|new_window=true] to reinstall the back cover, transfer and install the camera bezel, and replace the adhesive.
[* icon_note] If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.
[* icon_reminder] [guide|124003|Follow this guide|new_window=true] to reinstall the back cover and replace the adhesive.
[* icon_note] During reassembly, this is a good point to power on your phone and test all functions before you seal the back cover in place. Be sure to power your phone back down completely before you continue working.
[* icon_reminder] [guide|124003|Follow this guide|new_window=true] to reinstall the back cover, transfer and install the camera bezel, and replace the adhesive.
[* icon_note] If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

I tuoi contributi sono usati su licenza in base alla licenza open source Creative Commons.