Salta al contenuto principale
Cinese
Inglese

AirPods Charging Case Disassembly

Informazioni Guida

= Fatto = Incompleto

      Descrivi la parte specifica o il componente di questo device sul quale stai lavorando. Es: Batteria

      Crea un titolo.

      Questo breve sommario di 1-2 frasi apparirà nei risultati di ricerca.

      Comunica informazioni di base prima che il lettore si immerga nella guida.

      Passi Guida

      Passo 1

      This is a charging case for AirPods, which is currently waterlogged. I will try to take it apart and test the internals for water damage.

      Passo 2

      Find a pair of tweezer, and then divide it into two halves to create a spudger. Then grind it with a grinder to the size required to be reasonably long and thick, ready for the next step of disassembly!

      Passo 3

      Using a scalpel, insert the inside and outside to slide left and right so that the connection parts of the charging case are completely loose, and then lift a space and insert a tool as a lever.

      Passo 4

      Use a polished metal lever to loosen it further, then fix it with a vise grip, tighten it slowly to deform the load and outer shell, and then loosen with the tool. (Remember to secure the AirPods on both sides of the shell before attaching it. Prevent the press from leaving traces on the outer casing.)

      Passo 5

      After loosening, use a metal lever, pull both sides at the same time, then pay attention to the cable to pull out the internal base and finally heat with a hot air gun to remove the stainless steel internal fixed iron ring.

      Passo 6

      After removing the stainless steel fixed iron ring, then use a heat gun to heat, the indicator light and the charging contact base of the AirPods.

      Passo 7

      After heating the base of the contact, use a scalpel to open it. The adhering parts become loosened further so you can finally remove them from the bottom.

      Passo 8

      Heat with a hot air gun, cover the metal connection parts, the temperature here is slightly higher, about 90 to more than 100 degrees, after heating for 20 seconds.

      Passo 9

      After continuing to heat with a heat gun, loosen the battery with a lever, loosen the push button on the base of the fixed connection cable and remove the battery.

      Passo 10

      After removing the battery, remove the protective plate position, clean it with internal wash water and recharge it with an adjustable DC power supply.

      Passo 11

      Use the scalpel to slide the inner frame and fixed frame to the left and right to loosen the attachment parts. You can use the heating method to slide while heating, and then use the special metal lever polished before the hammer to force down.

      Passo 12

      Continue repeating the previous operation until it is completely loose, and finally remove the internal support.

      Passo 13

      After complete removal, remove it with a screwdriver and connect the cable at the base of the headset to the cable that is loaded with the lightning interface below.

      Passo 14

      After complete removal, a screwdriver is included and the cable is connected to the base of the headset to the cable that is loaded with the lightning interface below.

      Passo 15

      Después de retirar la placa de circuito, puede ver que algunos componentes de la placa de circuito están muy erosionados. Después de todo, el agua ha estado en el agua durante mucho tiempo.

      Passo 16

      Primer uso de la máquina de limpieza por ultrasonidos, con agua de lavado de PCB, trate de ahorrar.

      Passo 17

      Después de la limpieza, no te preocupes por la batería de litio todavía. Conecte la fuente de alimentación y vea si el indicador luminoso está encendido.

      Passo 18

      Casi olvido el botón que ifixit no desarmó completamente. ¿Cuál es el secreto dentro del botón? Por cierto, también le eché un vistazo. Puedo ver que es casi la misma que la clave interna del iPhone6 iphone5.

      Passo 19

      Resumen personal, el desmantelamiento de la caja de carga de AirPods está dirigido principalmente a los usuarios normales que han ingresado al agua por un largo tiempo, pueden intentar desmontarlos con este método, en la medida de lo posible, en el menor tiempo posible.

      I tuoi contributi sono usati su licenza in base alla licenza open source Creative Commons.