Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Componenti & Strumenti

Nota: Stai modificando un prerequisito per la guida che stavi visualizzando. Tutte le modifiche avranno effetto su tutte le 6guide che includono questo passo.

Inglese
Italiano

Traduzione in corso passo 2

Passo 2
Apply a suction cup to the right edge of the display as close as possible to the bottom of the device without overlapping the fingerprint sensor. Pull up on the suction cup with firm, constant pressure to create a slight gap along the bottom edge between the screen assembly and rear case. This may require a significant amount of force, but you only need to open a very slight gap with the suction cup to insert your tool.
Release the Screen Assembly
  • Apply a suction cup to the right edge of the display as close as possible to the bottom of the device without overlapping the fingerprint sensor.

  • Pull up on the suction cup with firm, constant pressure to create a slight gap along the bottom edge between the screen assembly and rear case.

  • This may require a significant amount of force, but you only need to open a very slight gap with the suction cup to insert your tool.

  • As the display on top of the screen assembly is flexible, you may end up separating the right edge of the display from the screen assembly instead of lifting the entire assembly. Try to pull up just the bottom edge of the screen assembly to prevent warping the display.

  • If you have trouble, apply more heat to further soften the adhesive, and try again. The adhesive cools quickly, so you may need to heat it repeatedly.

  • Insert an opening pick into the gap you opened behind the screen assembly.

  • Ensure your tool is behind the entire screen assembly and not just the display. You should notice a small plastic tab unclip from the device's frame if you have done this correctly.

Incunea lo strumento di apertura in plastica nella fessura creata dalla separazione tra schermo e scocca nell'angolo inferiore destro per tenerlo aperto.

Inserisci lo spudger in nylon nell'angolo inferiore sinistro dello schermo e fai leva per sollevare il display.

Continua a inserire gli strumenti di apertura in plastica e lo spudger tutto attorno al telefono e fai leva sullo schermo nei vari punti finché non si separa completamente dal dispositivo.

Rimuovi lo schermo con delicatezza e lentezza, altrimenti il display potrebbe rompersi.

[*title] Release the Screen Assembly
[*
black] WedgeApply a suction cup to the plastic opening tool betweenright edge of the gap created by separatingdisplay as close as possible to the screen and bodybottom of the phone indevice without overlapping the right hand corner to hold it openfingerprint sensor.
[* black] InsertPull up on the nylon spudger intosuction cup with firm, constant pressure to create a slight gap along the lower left corner ofbottom edge between the screen assembly and pryrear case.
[* icon_note] This may require a significant amount of force, but you only need to open a very slight gap with
the screen toward you.
[* black] Continue
suction cup to insert your tool.
[* icon_caution] As
the plastic opening and spudger tools around the phone, and pry opendisplay on top of the screen until itassembly is fully separatedflexible, you may end up separating the right edge of the display from the device.
[* icon_caution] Remove
screen assembly instead of lifting the entire assembly. Try to pull up just the bottom edge of the screen gentlyassembly to prevent warping the display.
[* icon_note] If you have trouble, apply more heat to further soften the adhesive,
and slowly astry again. The adhesive cools quickly, so you may need to heat it repeatedly.
[* black] Insert an opening pick into the gap you opened behind
the screen may crack otherwiseassembly.
[* icon_note] Ensure your tool is behind the entire screen assembly and not just the display. You should notice a small [https://d3nevzfk7ii3be.cloudfront.net/igi/KkMOORBHd5kCf4Om.full|plastic tab|new_window=true] unclip from the device's frame if you have done this correctly
.
[*title] Release the Screen Assembly
[*
black] WedgeApply a suction cup to the plastic opening tool betweenright edge of the gap created by separatingdisplay as close as possible to the screen and bodybottom of the phone indevice without overlapping the right hand corner to hold it openfingerprint sensor.
[* black] InsertPull up on the nylon spudger intosuction cup with firm, constant pressure to create a slight gap along the lower left corner ofbottom edge between the screen assembly and pryrear case.
[* icon_note] This may require a significant amount of force, but you only need to open a very slight gap with
the screen toward you.
[* black] Continue
suction cup to insert your tool.
[* icon_caution] As
the plastic opening and spudger tools around the phone, and pry opendisplay on top of the screen until itassembly is fully separatedflexible, you may end up separating the right edge of the display from the device.
[* icon_caution] Remove
screen assembly instead of lifting the entire assembly. Try to pull up just the bottom edge of the screen gentlyassembly to prevent warping the display.
[* icon_note] If you have trouble, apply more heat to further soften the adhesive,
and slowly astry again. The adhesive cools quickly, so you may need to heat it repeatedly.
[* black] Insert an opening pick into the gap you opened behind
the screen may crack otherwiseassembly.
[* icon_note] Ensure your tool is behind the entire screen assembly and not just the display. You should notice a small [https://d3nevzfk7ii3be.cloudfront.net/igi/KkMOORBHd5kCf4Om.full|plastic tab|new_window=true] unclip from the device's frame if you have done this correctly
.

I tuoi contributi sono usati su licenza in base alla licenza open source Creative Commons.