Salta al contenuto principale

Aggiusta la tua roba

Diritto alla Riparazione

Componenti & Strumenti

Nota: Stai modificando un prerequisito per la guida che stavi visualizzando. Tutte le modifiche avranno effetto su tutte le 6guide che includono questo passo.

Inglese
Italiano

Traduzione in corso passo 1

Passo 1
Power your phone off before you begin.
Heat the Screen Adhesive
  • Power your phone off before you begin.

  • If possible, drain the battery before disassembly. When the battery is charged, there's increased risk of a dangerous thermal event if the battery is overheated or damaged during repairs.

  • Prepare an iOpener and heat the front of the phone along its bottom edge for about two minutes, or until it's slightly too hot to touch. This will help soften the adhesive securing the screen assembly.

  • You may need to reheat and reapply the iOpener several times to get the phone warm enough. Follow the iOpener instructions to avoid overheating.

  • Since the display is made of plastic, it is especially susceptible to warping and display damage. If you notice the display bubbling up or wrinkling, stop heating immediately and cool down the device before trying again.

  • A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the device.

Disponi il telefono su una superficie piatta con lo schermo rivolto verso l'alto.

Inserisci l'estremità piatta di uno spudger in nylon nella fessura tra lo schermo e la scocca nell'angolo inferiore destro del telefono.

Fai leva per aprire parte dello schermo alzando l'attrezzo e lo schermo verso di te.

Può essere necessario usare un apporto di calore, ad esempio con un iOpener, per riscaldare l'adesivo sottostante e ammorbidirlo prima di tentare l'apertura.

[* black] Place thetitle] Heat the Screen Adhesive
[* icon_caution] Power your
phone onoff before you begin.
[* icon_note] If possible, drain the battery before disassembly. When the battery is charged, there's increased risk of
a flat surface withdangerous thermal event if the screen facing upbattery is overheated or damaged during repairs.
[* black] Insert[guide|25705|Prepare an iOpener|new_window=true] and heat the flat endfront of a nylon spudger into the crease separatingphone along its bottom edge for about two minutes, or until it's slightly too hot to touch. This will help soften the adhesive securing the screen assembly.
[* icon_note] You may need to reheat
and reapply the body iniOpener several times to get the lower right corner ofphone warm enough. Follow the phoneiOpener instructions to avoid overheating.
[* black] Pry open particon_caution] Since the display is made of plastic, it is especially susceptible to warping and display damage. If you notice the screen by pulling the tooldisplay bubbling up or wrinkling, stop heating immediately and cool down the screen toward youdevice before trying again.
[* icon_note] YouA hair dryer, heat gun, or hot plate may also be used, but be requiredcareful not to use a heating element, such asoverheat the [guide|11677|iOpener], to heat and loosen the adhesive underneath before attempting to pry it opendevice.
[* black] Place thetitle] Heat the Screen Adhesive
[* icon_caution] Power your
phone onoff before you begin.
[* icon_note] If possible, drain the battery before disassembly. When the battery is charged, there's increased risk of
a flat surface withdangerous thermal event if the screen facing upbattery is overheated or damaged during repairs.
[* black] Insert[guide|25705|Prepare an iOpener|new_window=true] and heat the flat endfront of a nylon spudger into the crease separatingphone along its bottom edge for about two minutes, or until it's slightly too hot to touch. This will help soften the adhesive securing the screen assembly.
[* icon_note] You may need to reheat
and reapply the body iniOpener several times to get the lower right corner ofphone warm enough. Follow the phoneiOpener instructions to avoid overheating.
[* black] Pry open particon_caution] Since the display is made of plastic, it is especially susceptible to warping and display damage. If you notice the screen by pulling the tooldisplay bubbling up or wrinkling, stop heating immediately and cool down the screen toward youdevice before trying again.
[* icon_note] YouA hair dryer, heat gun, or hot plate may also be used, but be requiredcareful not to use a heating element, such asoverheat the [guide|11677|iOpener], to heat and loosen the adhesive underneath before attempting to pry it opendevice.

I tuoi contributi sono usati su licenza in base alla licenza open source Creative Commons.